SC1200UFH-266 AMD (ADVANCED MICRO DEVICES), SC1200UFH-266 Datasheet - Page 285

• Manufacturer Part Number: SC1200UFH-266
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of SC1200UFH-266

• Operating Temperature (min): 0C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Lead Free Status / Rohs Status: Not Compliant

Core Logic Module - USB Controller Registers - PCIUSB
AMD Geode™ SC1200/SC1201 Processor Data Book
Index 14h-2Bh
Index 2Ch-2Dh
Index 2Eh-2Fh
Index 30h-3Bh
Index 3Ch
This register identifies the system interrupt controllers to which the device’s interrupt pin is connected. The value of this register is used
by device drivers and has no direct meaning to USB.
Index 3Dh
This register selects which interrupt pin the device uses. USB uses INTA# after reset. INTB#, INTC# or INTD# can be selected by writ-
ing 2, 3 or 4, respectively.
Index 3Eh
This register specifies how long a burst is needed by the USB, assuming a clock rate of 33 MHz. The value in this register specifies a
period of time in units of 1/4 microsecond.
Index 3Fh
This register specifies how often (in units of 1/4 microsecond) the USB needs access to the PCI bus assuming a clock rate of 33 MHz.
Index 40h-43h
Used for internal debug and test purposes only.
Index 44h
Index 45h-FFh
Offset 00h-03h
Offset 04h-07h
31:11
31:8
Bit
7:1
Bit
7:0
10
9
8
0
Description
Write Only. Read as 0s.
Data Buffer Region 16.
0: The size of the region for the data buffer is 32 bytes.
1: The size of the region for the data buffer is 16 bytes.
Description
Reserved. Read/Write 0s.
Revision (Read Only). Indicates the Open HCI Specification revision number implemented by the Hardware. USB sup-
ports 1.0 specification. (X.Y = XYh).
Reserved. Read/Write 0s.
RemoteWakeupConnectedEnable. If a remote wakeup signal is supported, this bit enables that operation. Since there is
no remote wakeup signal supported, this bit is ignored.
RemoteWakeupConnected (Read Only). This bit indicated whether the HC supports a remote wakeup signal. This imple-
mentation does not support any such signal. The bit is hard-coded to 0.
InterruptRouting. This bit is used for interrupt routing:
0: Interrupts routed to normal interrupt mechanism (INT).
1: Interrupts routed to SMI.
Table 6-41. PCIUSB: USB PCI Configuration Registers (Continued)
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers
ASIC Operational Mode Enable Register (R/W)
ASIC Test Mode Enable Register (R/W)
Interrupt Line Register (R/W)
Interrupt Pin Register (R/W)
Max. Latency Register (RO)
Subsystem Vendor ID (RO)
HcRevision Register (RO)
HcControl Register (R/W)
Min. Grant Register (RO)
Subsystem ID (RO)
Reserved
Reserved
Reserved
32579B
Reset Value = 00000110h
Reset Value = 00000000h
Reset Value: 000F0000h
Reset Value: A0F8h
Reset Value: 0E11h
Reset Value: 00h
Reset Value: 01h
Reset Value: 00h
Reset Value: 50h
Reset Value: 00h
Reset Value: 00h
Reset Value: 00h
Reset Value: 00h
285