SC1200UFH-266 AMD (ADVANCED MICRO DEVICES), SC1200UFH-266 Datasheet - Page 339

• Manufacturer Part Number: SC1200UFH-266
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of SC1200UFH-266

• Operating Temperature (min): 0C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Lead Free Status / Rohs Status: Not Compliant

Video Processor Module - Video Processor Registers - Function 4
AMD Geode™ SC1200/SC1201 Processor Data Book
Offset 04h-07h
General configuration register for display control. This register is also used to determine how graphics and video data are to be com-
bined in the display on the output device.
30:28
19:17
16:14
13:10
Bit
31
27
26
25
24
23
22
21
20
0
9
Table 7-9. F4BAR0+Memory Offset: Video Processor Configuration Registers (Continued)
Description
VID_EN (Video Enable). Enables video acceleration hardware.
0: Disable (reset) video module.
1: Enable.
DDC_SDA_IN (DDC Input Data). (Read Only) Returns the value from the DDC_SDA signal (muxed with IDE_DATA9) con-
nected to pin 12 of the VGA connector.
Reserved.
FP_ON_STATUS (Flat Panel On Status). (Read Only) Shows whether power to the attached flat panel is on or off. This bit
transitions at the end of the power-up or power-down sequence.
0: Power to the flat panel is off.
1: Power to the flat panel is on.
DAC_VREF (CRT DAC Voltage Reference). When set to 1, this bit enables use of an external voltage reference for CRT
DAC.
0: Disable external VREF. Enable Internal VREF.
1: Use external VREF. Connect an external voltage reference to the VREF signal.
Reserved. Must be set to 0.
DDC_OE (DDC Output Enable). Selects the direction of signal DDC_SDA (muxed with IDE_DATA9). This bit indicates the
direction of DDC data flow between the Video Processor and a CRT.
0: Input.
1: Output. DDC data is sent from the Video Processor to the CRT.
DDC_SDA_OUT (DDC Output Data). DDC data bit for output.
DDC_SCL (DDC Serial Clock). Provides the serial clock for the interface using the DDC_SCL signal (muxed with
IDE_DATA10).
GV_GAMMA_SEL (Graphics or Video Gamma Source Data). Selects whether the graphics or video data goes to the
Gamma Correction RAM. GAMMA_EN (F4BAR0+Memory Offset 28h[0]) must be enabled for the selected data source to
pass through the Gamma Correction RAM.
0: Graphics data to Gamma Correction RAM.
1: Video data to Gamma Correction RAM.
Note:
COLOR_CHROMA_SEL (Color or Chroma Key Select). Selects whether the graphics is used for color keying or the video
data stream is used for chroma keying.
0: Graphics data is compared to the color key.
1: Video data is compared to the chroma key.
PWR_SEQ_DLY (Power Sequence Delay). Selects the number of frame periods that transpire between successive transi-
tions of the power sequence control lines.
CRT_SYNC_SKW (CRT Sync Skew). Represents the number of pixel clocks to skew the horizontal and vertical sync that
are sent to the CRT. This field should be programmed to 100 at the baseline. Via this register, the sync can be moved for-
ward (later) or backward (earlier) relative to the pixel data. This register can be used to compensate for possible delay of
pixel data being processed via the Video Processor.
000: Sync moved 4 clocks backward
001: Sync moved 3 clocks backward
010: Sync moved 2 clocks backward
011: Sync moved 1 clock backward
Reserved.
CRT_VSYNC_POL (CRT Vertical Synchronization Polarity). Selects CRT vertical sync polarity.
0: CRT vertical sync is normally low, and is set high during the sync interval.
1: CRT vertical sync is normally high, and is set low during the sync interval.
Gamma Correction is always in the RGB domain for graphics data.
Gamma Correction can be in the YUV or RGB domain for video data.
Display Configuration Register (R/W)
100: Baseline, sync not moved
101: Sync moved 1 clock forward
110: Sync moved 2 clocks forward
111: Sync moved 3 clocks forward
32579B
Reset Value: x0000000h
339