SC1200UFH-266 AMD (ADVANCED MICRO DEVICES), SC1200UFH-266 Datasheet - Page 295

• Manufacturer Part Number: SC1200UFH-266
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of SC1200UFH-266

• Operating Temperature (min): 0C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Lead Free Status / Rohs Status: Not Compliant

Core Logic Module - USB Controller Registers - PCIUSB
AMD Geode™ SC1200/SC1201 Processor Data Book
Offset 100h-103h
Note:
Offset 104h-107h
Note:
Offset 108h-10Bh
Note:
Offset 10Ch-10Fh
Note:
31:9
31:8
31:8
31:8
Bit
7:0
7:0
8
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
This register is used to enable and control the emulation hardware and report various status information.
This register is the emulation side of the legacy Input Buffer register.
This register is the emulation side of the legacy Output Buffer register where keyboard and mouse data is to be written by soft-
ware.
This register is the emulation side of the legacy Status register.
Description
Reserved. Read/Write 0s.
A20State. Indicates current state of Gate A20 on keyboard controller. Compared against value written to 60h when
GateA20Sequence is active.
IRQ12Active. Indicates a positive transition on IRQ12 from keyboard controller occurred. Software writes this bit to 1 to
clear it (set it to 0); a 0 write has no effect.
IRQ1Active. Indicates a positive transition on IRQ1 from keyboard controller occurred. Software writes this bit to 1 to clear
it (set it to 0); a 0 write has no effect.
GateA20Sequence. Set by HC when a data value of D1h is written to I/O port 64h. Cleared by HC on write to I/O port 64h
of any value other than D1h.
ExternalIRQEn. When set to 1, IRQ1 and IRQ12 from the keyboard controller cause an emulation interrupt. The function
controlled by this bit is independent of the setting of the EmulationEnable bit in this register.
IRQEn. When set, the HC generates IRQ1 or IRQ12 as long as the OutputFull bit in HceStatus is set to 1. If the AuxOutput-
Full bit of HceStatus is 0, IRQ1 is generated: if 1, then an IRQ12 is generated.
CharacterPending. When set, an emulation interrupt will be generated when the OutputFull bit of the HceStatus register is
set to 0.
EmulationInterrupt (Read Only). This bit is a static decode of the emulation interrupt condition.
EmulationEnable. When set to 1 the HC is enabled for legacy emulation and will decode accesses to I/O registers 60h
and 64h and generate IRQ1 and/or IRQ12 when appropriate. The HC also generates an emulation interrupt at appropriate
times to invoke the emulation software.
Reserved. Read/Write 0s.
InputData. This register holds data written to I/O ports 60h and 64h.
Reserved. Read/Write 0s.
OutputData. This register hosts data that is returned when an I/O read of port 60h is performed by application software.
Reserved. Read/Write 0s.
Parity. Indicates parity error on keyboard/mouse data.
Timeout. Used to indicate a time-out
AuxOutputFull. IRQ12 is asserted whenever this bit is set to 1 and OutputFull is set to 1 and the IRQEn bit is set.
Inhibit Switch. This bit reflects the state of the keyboard inhibit switch and is set if the keyboard is NOT inhibited.
CmdData. The HC will set this bit to 0 on an I/O write to port 60h and on an I/O write to port 64h the HC will set this bit to 1.
Flag. Nominally used as a system flag by software to indicate a warm or cold boot.
InputFull. Except for the case of a Gate A20 sequence, this bit is set to 1 on an I/O write to address 60h or 64h. While this
bit is set to 1 and emulation is enabled, an emulation interrupt condition exists.
OutputFull. The HC will set this bit to 0 on a read of I/O port 60h. If IRQEn is set and AuxOutputFull is set to 0 then an
IRQ1 is generated as long as this bit is set to 1. If IRQEn is set and AuxOutputFull is set to 1 then and IRQ12 will be gener-
ated a long as this bit is set to 1. While this bit is 0 and CharacterPending in HceControl is set to 1, an emulation interrupt
condition exists.
Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)
HceControl Register (R/W)
HceOutput Register (R/W)
HceStatus Register (R/W)
HceInput Register (R/W)
32579B
Reset Value = 00000000h
Reset Value = 000000xxh
Reset Value = 000000xxh
Reset Value = 00000000h
295