ST52F513G3M6 STMicroelectronics, ST52F513G3M6 Datasheet - Page 79

• Manufacturer Part Number: ST52F513G3M6
• Manufacturer: STMicroelectronics

Specifications of ST52F513G3M6

• Cpu Family: ST52
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: I2C/SCI/SPI
• Program Memory Type: Flash
• Program Memory Size: 8KB
• Total Internal Ram Size: 256Byte
• # I/os (max): 22
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: SO
• Lead Free Status / Rohs Status: Compliant

PWM/Timer 0 Counter Low Output Register
(PWM0_COUNT_OUT_L)
Output Register 8 (08h) Write only
Reset Value: 0000 0000 (00h)
Bit 7-0: T0CO7-0 PWM/Timer 0 Counter LSB
This register is used to write the Timer 0 Counter
value (LSB).
Note:
PWM0_COUNT_OUT_x couple is latched in the
internal registers of the peripherals. For this
reason, this register should be written after the
MSB one.
PWM/Timer 0 Reload High Output Register
(PWM0_RELOAD_H)
Output Register 9 (09h) Write only
Reset Value: 1111 1111 (0FFh)
Bit 7-0: T0REL15-8 PWM/Timer 0 Reload MSB
This register is used to write the Timer 0 Reload
value (MSB).
Note: this register is latched after writing the LSB
part (PWM0_RELOAD_L: see below). For this
reason, this register must be written before the
LSB.
PWM/Timer 0 Reload Low Output Register
(PWM0_RELOAD_L)
Output Register 10 (0Ah) Write only
Reset Value: 1111 1111 (0FFh)
Bit 7-0: T0REL7-0 PWM/Timer 0 Reload LSB
This register is used to write the Timer 0 Reload
value (LSB).
T0REL15 T0REL14 T0REL13 T0REL12 T0REL11 T0REL10 T0REL9 T0REL8
T0REL7 T0REL6 T0REL5 T0REL4 T0REL3 T0REL2 T0REL1 T0REL0
T0CO7
7
7
7
T0CO6
writing
T0CO5
T0CO4
this
T0CO3
T0CO2
register,
T0CO1
T0CO0
0
0
0
the
Note:
PWM0_RELOAD_x couple is latched in the
internal registers of the peripherals. For this reason
this register should be written after the MSB one.
12.6 PWM/Timer 1 Register Description
The following registers are related to the use of the
PWM/Timer 1.
12.6.1 PWM/Timer 1 Configuration Registers.
PWM/Timer 1 Control Register 1 (PWM1_CR1)
Configuration Register 12 (0Ch) Read/Write
Reset Value: 0000 0000 (00h)
Bit 7: T1MOD PWM/Timer 1 Mode
Bit 6: T1IES Interrupt on Stop signal Enable
Bit 5: T1IEF Interrupt on T1OUT falling Enable
Bit 4: T1IER Interrupt on T1OUT rising Enable
Bit 3: not used: it must be left at reset status
Bit 2: T1STRT PWM/Timer 1 Start bit
Bit 1: not used: it must be left at reset status
Bit 0: T1RES PWM/Timer 1 Reset bit
T1MOD
7
0: Timer Mode
1: PWM Mode
0: interrupt disabled
1: interrupt enabled
0: interrupt disabled
1: interrupt enabled
0: interrupt disabled
1: interrupt enabled
0: Timer 1 stopped
1: Timer 1 started
0: PWM/Timer 1 reset
1: PWM/Timer 1 set
T1IES
by
T1IEF
writing
T1IER
ST52510xx ST52513xx
this
-
T1STRT
register,
-
79/136
T1RES
0
the