SAM3S4B Atmel Corporation, SAM3S4B Datasheet - Page 1056
SAM3S4B
Manufacturer Part Number
SAM3S4B
Description
Manufacturer
Atmel Corporation
Specifications of SAM3S4B
Flash (kbytes)
256 Kbytes
Pin Count
64
Max. Operating Frequency
64 MHz
Cpu
Cortex-M3
# Of Touch Channels
23
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
10
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
48
Self Program Memory
YES
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- Current page: 1056 of 1118
- Download datasheet (24Mb)
41.4.9
41.4.9.1
41.4.9.2
1056
SAM3S
Crystal Oscillators Design Consideration Information
Choosing a Crystal
Printed Circuit Board (PCB)
When choosing a crystal for the 32768 Hz Slow Clock Oscillator or for the 3-20 MHz Oscillator,
several parameters must be taken into account. Important parameters between crystal and
SAM3S specifications are as follows:
SAM3S Oscillators are low power oscillators requiring particular attention when designing PCB
systems.
• Load Capacitance
• Drive Level
• Equivalent Series Resistor (ESR)
• Shunt Capacitance
– C
– Crystal drive level >= Oscillator Drive Level. Having a crystal drive level number
– Crystal ESR <= Oscillator ESR Max. Having a crystal with ESR value higher than
– Max. crystal Shunt capacitance <= Oscillator Shunt Capacitance (
order to oscillate at the target frequency. The crystal must be chosen according to
the internal load capacitance (C
load capacitance will result in a frequency drift.
lower than the oscillator specification may damage the crystal.
the oscillator may cause the oscillator to not start.
crystal with ESR value higher than the oscillator may cause the oscillator to not start.
crystal
is the equivalent capacitor value the oscillator must “show” to the crystal in
L
) of the on-chip oscillator. Having a mismatch for the
C
SHUNT
6500C–ATARM–8-Feb-11
).
Having a
Related parts for SAM3S4B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: