SAM3S4B Atmel Corporation, SAM3S4B Datasheet - Page 90

• Manufacturer Part Number: SAM3S4B
• Manufacturer: Atmel Corporation

Specifications of SAM3S4B

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 48
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.12.2.5
10.12.2.6
10.12.2.7
90
SAM3S
Post-indexed addressing
Restrictions
Condition flags
The address obtained from the register Rn is used as the address for the memory access. The
offset value is added to or subtracted from the address, and written back into the register Rn.
The assembly language syntax for this mode is:
The value to load or store can be a byte, halfword, word, or two words. Bytes and halfwords can
either be signed or unsigned. See
Table 10-18
Table 10-18. Offset ranges
For load instructions:
When Rt is PC in a word load instruction:
For store instructions:
These instructions do not change the flags.
Instruction type
Word, halfword, signed
halfword, byte, or signed
byte
Two words
• Rt can be SP or PC for word loads only
• Rt must be different from Rt2 for two-word loads
• Rn must be different from Rt and Rt2 in the pre-indexed or post-indexed forms.
• bit[0] of the loaded value must be 1 for correct execution
• a branch occurs to the address created by changing bit[0] of the loaded value to 0
• if the instruction is conditional, it must be the last instruction in the IT block.
• Rt can be SP for word stores only
• Rt must not be PC
• Rn must not be PC
• Rn must be different from Rt and Rt2 in the pre-indexed or post-indexed forms.
[Rn, #offset]!
[Rn], #offset
shows the ranges of offset for immediate, pre-indexed and post-indexed forms.
Immediate offset
−255 to 4095
multiple of 4 in the
range −1020 to
1020
“Address alignment” on page
Pre-indexed
−255 to 255
multiple of 4 in the
range −1020 to
1020
83.
Post-indexed
−255 to 255
multiple of 4 in the
range −1020 to
1020
6500C–ATARM–8-Feb-11