SAM3S4B Atmel Corporation, SAM3S4B Datasheet - Page 18

• Manufacturer Part Number: SAM3S4B
• Manufacturer: Atmel Corporation

Specifications of SAM3S4B

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 48
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

18
SAM3S
Figure 5-1.
Note:
Figure 5-2.
Note:
Figure 5-3
Since the PIO state is preserved when in backup mode, any free PIO line can be used to switch
off the external regulator by driving the PIO line at low level (PIO is input, pull-up enabled after
backup reset). External wake-up of the system can be from a push button or any signal. See
Section 5.6 “Wake-up Sources”
Restrictions
With Main Supply < 2.0 V, USB and ADC/DAC and Analog comparator are not usable.
With Main Supply ≥ 2.0V and < 3V, USB is not usable.
With Main Supply ≥ 3V, all peripherals are usable.
Restrictions
With Main Supply < 2.0V, USB is not usable.
With VDDIN < 2.0V, ADC/DAC and Analog comparator are not usable.
With Main Supply ≥ 2.0V and < 3V, USB is not usable.
With Main Supply and VDDIN ≥ 3V, all peripherals are usable.
below provides an example of the powering scheme when using a backup battery.
Single Supply
Core Externally Supplied
ADC, DAC, Analog
Comparator Supply
(2.0V-3.6V)
VDDCORE Supply
(1.62V-1.95V)
Main Supply
(1.62V-3.6V)
Main Supply
(1.8V-3.6V)
Can be the
same supply
for further details.
VDDIO
VDDIN
VDDOUT
VDDCORE
VDDPLL
VDDIO
VDDIN
VDDOUT
VDDCORE
VDDPLL
Analog Comp.
Transceivers.
ADC, DAC
Regulator
Analog Comp.
Voltage
Transceivers.
Regulator
ADC, DAC
USB
Voltage
USB
6500C–ATARM–8-Feb-11