SAM3S4B Atmel Corporation, SAM3S4B Datasheet - Page 313

• Manufacturer Part Number: SAM3S4B
• Manufacturer: Atmel Corporation

Specifications of SAM3S4B

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 48
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.2.5
19.2.5.1
6500C–ATARM–8-Feb-11
Device Operations
Flash Read Command
Several commands on the Flash memory are available. These commands are summarized in
Table 19-3 on page
face running several read/write handshaking sequences.
When a new command is executed, the previous one is automatically achieved. Thus, chaining
a read command after a write automatically flushes the load buffer in the Flash.
In the following tables,
This command is used to read the contents of the Flash memory. The read command can start
at any valid address in the memory plane and is optimized for consecutive reads. Read hand-
shaking can be chained; an internal address buffer is automatically increased.
Table 19-6.
Table 19-7.
Step
1
2
3
4
5
...
n
n+1
n+2
n+3
...
Step
1
2
3
4
5
6
7
...
n
• DATA[15:0] pertains to ASAM3SxB/C (64/100 pins)
• DATA[7:0] pertains to SAM3SxA (48 pins)
Handshake Sequence
Write handshaking
Write handshaking
Write handshaking
Read handshaking
Read handshaking
...
Write handshaking
Write handshaking
Read handshaking
Read handshaking
...
Handshake Sequence
Write handshaking
Write handshaking
Write handshaking
Write handshaking
Write handshaking
Read handshaking
Read handshaking
...
Write handshaking
Read Command
Read Command
309. Each command is driven by the programmer through the parallel inter-
Table 19-6
through
MODE[3:0]
CMDE
ADDR0
ADDR1
DATA
DATA
...
ADDR0
ADDR1
DATA
DATA
...
MODE[3:0]
CMDE
ADDR0
ADDR1
ADDR2
ADDR3
DATA
DATA
...
ADDR0
Table 19-17
DATA[15:0]
READ
Memory Address LSB
Memory Address
*Memory Address++
*Memory Address++
...
Memory Address LSB
Memory Address
*Memory Address++
*Memory Address++
...
DATA[7:0]
READ
Memory Address LSB
Memory Address
Memory Address
Memory Address
*Memory Address++
*Memory Address++
...
Memory Address LSB
SAM3S
313