SAM3S4B Atmel Corporation, SAM3S4B Datasheet - Page 163
SAM3S4B
Manufacturer Part Number
SAM3S4B
Description
Manufacturer
Atmel Corporation
Specifications of SAM3S4B
Flash (kbytes)
256 Kbytes
Pin Count
64
Max. Operating Frequency
64 MHz
Cpu
Cortex-M3
# Of Touch Channels
23
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
10
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
48
Self Program Memory
YES
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- Current page: 163 of 1118
- Download datasheet (24Mb)
10.20.10 NVIC design hints and tips
10.20.10.1
6500C–ATARM–8-Feb-11
NVIC programming hints
Ensure software uses correctly aligned register accesses. The processor does not support
unaligned accesses to NVIC registers. See the individual register descriptions for the supported
access sizes.
A interrupt can enter pending state even it is disabled.
Before programming VTOR to relocate the vector table, ensure the vector table entries of the
new vector table are setup for fault handlers and all enabled exception like interrupts. For more
information see
Software uses the CPSIE I and CPSID I instructions to enable and disable interrupts. The
CMSIS provides the following intrinsic functions for these instructions:
In addition, the CMSIS provides a number of functions for NVIC control, including:
Table 10-29. CMSIS functions for NVIC control
For more information about these functions see the CMSIS documentation.
CMSIS interrupt control function
void NVIC_SetPriorityGrouping(uint32_t
priority_grouping)
void NVIC_EnableIRQ(IRQn_t IRQn)
void NVIC_DisableIRQ(IRQn_t IRQn)
uint32_t NVIC_GetPendingIRQ (IRQn_t IRQn)
void NVIC_SetPendingIRQ (IRQn_t IRQn)
void NVIC_ClearPendingIRQ (IRQn_t IRQn)
uint32_t NVIC_GetActive (IRQn_t IRQn)
void NVIC_SetPriority (IRQn_t IRQn, uint32_t priority)
uint32_t NVIC_GetPriority (IRQn_t IRQn)
void NVIC_SystemReset (void)
void __disable_irq(void) // Disable Interrupts
void __enable_irq(void) // Enable Interrupts
“Vector Table Offset Register” on page
Return true if IRQn is pending
Set priority for IRQn
Read priority of IRQn
Description
Set the priority grouping
Enable IRQn
Disable IRQn
Set IRQn pending
Clear IRQn pending status
Return the IRQ number of the active
interrupt
Reset the system
170.
SAM3S
163
Related parts for SAM3S4B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: