IC MCU 8BIT 3MHZ 52-PLCC

MC68HC11E0CFNE3

Manufacturer Part NumberMC68HC11E0CFNE3
DescriptionIC MCU 8BIT 3MHZ 52-PLCC
ManufacturerFreescale Semiconductor
SeriesHC11
MC68HC11E0CFNE3 datasheets
 

Specifications of MC68HC11E0CFNE3

Core ProcessorHC11Core Size8-Bit
Speed3MHzConnectivitySCI, SPI
PeripheralsPOR, WDTNumber Of I /o38
Program Memory TypeROMlessRam Size512 x 8
Voltage - Supply (vcc/vdd)4.5 V ~ 5.5 VData ConvertersA/D 8x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case52-PLCCController Family/series68HC11
No. Of I/o's38Ram Memory Size512Byte
Cpu Speed3MHzNo. Of Timers1
Embedded Interface TypeSCI, SPIDigital Ic Case StyleLCC
Rohs CompliantYesProcessor SeriesHC11E
CoreHC11Data Bus Width8 bit
Data Ram Size512 BInterface TypeSCI, SPI
Maximum Clock Frequency3 MHzNumber Of Programmable I/os38
Number Of Timers8Maximum Operating Temperature+ 85 C
Mounting StyleSMD/SMTMinimum Operating Temperature- 40 C
On-chip Adc8 bit, 8 ChannelLead Free Status / RoHS StatusLead free / RoHS Compliant
Eeprom Size-Program Memory Size-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Page 41
42
Page 42
43
Page 43
44
Page 44
45
Page 45
46
Page 46
47
Page 47
48
Page 48
49
Page 49
50
Page 50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
Page 45/124

Download datasheet (7Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
RESETS AND INTERRUPTS
Resets and interrupt operations load the program counter with a vector that points to
a new location from which instructions are to be fetched. A reset immediately stops
execution of the current instruction and forces the program counter to a known starting
address. Internal registers and control bits are initialized so the MCU can resume ex-
ecuting instructions. An interrupt temporarily suspends normal program execution
while an interrupt service routine is being executed. After an interrupt has been ser-
viced, the main program resumes as if there had been no interruption.
5.1 Resets
There are four possible sources of reset. Power-on reset (POR) and external reset
share the normal reset vector. The computer operating properly (COP) system and the
clock monitor each has its own vector.
5.1.1 Power-On Reset
A positive transition on V
DD
power-up conditions. POR cannot be used to detect drops in power supply voltages.
A 4064 t
(internal clock cycle) delay after the oscillator becomes active allows the
CYC
clock generator to stabilize. If RESET is at logical zero at the end of 4064 t
CPU remains in the reset condition until goes to logical one.
It is important to protect the MCU during power transitions. Most M68HC11 systems
need an external circuit that holds the RESET pin low whenever V
imum operating level. This external voltage level detector, or other external reset cir-
cuits, are the usual source of reset in a system. The POR circuit only initializes internal
circuitry during cold starts. Refer to Figure 2-3.
5.1.2 External Reset (RESET)
The CPU distinguishes between internal and external reset conditions by sensing
whether the reset pin rises to a logic one in less than two E-clock cycles after an inter-
nal device releases reset. When a reset condition is sensed, the RESET pin is driven
low by an internal device for four E-clock cycles, then released. Two E-clock cycles
later it is sampled. If the pin is still held low, the CPU assumes that an external reset
has occurred. If the pin is high, it indicates that the reset was initiated internally by ei-
ther the COP system or the clock monitor. It is not advisable to connect an external
resistor capacitor (RC) power-up delay circuit to the reset pin of M68HC11 devices be-
cause the circuit charge time constant can cause the device to misinterpret the type of
reset that occurred.
5.1.3 COP Reset
The MCU includes a COP system to help protect against software failures. When the
TECHNICAL DATA
For More Information On This Product,
SECTION 5
generates a power-on reset (POR), which is used only for
RESETS AND INTERRUPTS
Go to: www.freescale.com
, the
CYC
is below the min-
DD
5-1