IC MCU 8BIT 3MHZ 52-PLCC

MC68HC11E0CFNE3

Manufacturer Part NumberMC68HC11E0CFNE3
DescriptionIC MCU 8BIT 3MHZ 52-PLCC
ManufacturerFreescale Semiconductor
SeriesHC11
MC68HC11E0CFNE3 datasheets
 

Specifications of MC68HC11E0CFNE3

Core ProcessorHC11Core Size8-Bit
Speed3MHzConnectivitySCI, SPI
PeripheralsPOR, WDTNumber Of I /o38
Program Memory TypeROMlessRam Size512 x 8
Voltage - Supply (vcc/vdd)4.5 V ~ 5.5 VData ConvertersA/D 8x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case52-PLCCController Family/series68HC11
No. Of I/o's38Ram Memory Size512Byte
Cpu Speed3MHzNo. Of Timers1
Embedded Interface TypeSCI, SPIDigital Ic Case StyleLCC
Rohs CompliantYesProcessor SeriesHC11E
CoreHC11Data Bus Width8 bit
Data Ram Size512 BInterface TypeSCI, SPI
Maximum Clock Frequency3 MHzNumber Of Programmable I/os38
Number Of Timers8Maximum Operating Temperature+ 85 C
Mounting StyleSMD/SMTMinimum Operating Temperature- 40 C
On-chip Adc8 bit, 8 ChannelLead Free Status / RoHS StatusLead free / RoHS Compliant
Eeprom Size-Program Memory Size-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Page 61
62
Page 62
63
Page 63
64
Page 64
65
Page 65
66
Page 66
67
Page 67
68
Page 68
69
Page 69
70
Page 70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
Page 67/124

Download datasheet (7Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
SERIAL COMMUNICATIONS INTERFACE
The serial communications interface (SCI) is a universal asynchronous receiver trans-
mitter (UART), one of two independent serial I/O subsystems in the MC68HC11D3. It
has a standard nonreturn to zero (NRZ) format (one start, eight or nine data, and one
stop bit). Several baud rates are available. The SCI transmitter and receiver are inde-
pendent, but use the same data format and bit rate.
7.1 Data Format
The serial data format requires the following conditions:
1. An idle line in the high state before transmission or reception of a message
2. A start bit, logic zero, transmitted or received, that indicates the start of each
character
3. Data that is transmitted and received least significant bit (LSB) first
4. A stop bit, logic one, used to indicate the end of a frame (A frame consists of a
start bit, a character of eight or nine data bits, and a stop bit.)
5. A break (defined as the transmission or reception of a logic zero for some mul-
tiple number of frames).
Selection of the word length is controlled by the M bit of SCI control register SCCR1.
7.2 Transmit Operation
The SCI transmitter includes a parallel transmit data register (SCDR) and a serial shift
register. The contents of the serial shift register can only be written through the SCDR.
This double buffered operation allows a character to be shifted out serially while an-
other character is waiting in the SCDR to be transferred into the serial shift register.
The output of the serial shift register is applied to TxD as long as transmission is in
progress or the transmit enable (TE) bit of serial communication control register 2
(SCCR2) is set. The block diagram, Figure 7-1, shows the transmit serial shift register,
and the buffer logic at the top of the figure.
SERIAL COMMUNICATIONS INTERFACE
TECHNICAL DATA
For More Information On This Product,
SECTION 7
Go to: www.freescale.com
7-1