IC MCU 8BIT 3MHZ 52-PLCC

MC68HC11E0CFNE3

Manufacturer Part NumberMC68HC11E0CFNE3
DescriptionIC MCU 8BIT 3MHZ 52-PLCC
ManufacturerFreescale Semiconductor
SeriesHC11
MC68HC11E0CFNE3 datasheets
 


Specifications of MC68HC11E0CFNE3

Core ProcessorHC11Core Size8-Bit
Speed3MHzConnectivitySCI, SPI
PeripheralsPOR, WDTNumber Of I /o38
Program Memory TypeROMlessRam Size512 x 8
Voltage - Supply (vcc/vdd)4.5 V ~ 5.5 VData ConvertersA/D 8x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case52-PLCCController Family/series68HC11
No. Of I/o's38Ram Memory Size512Byte
Cpu Speed3MHzNo. Of Timers1
Embedded Interface TypeSCI, SPIDigital Ic Case StyleLCC
Rohs CompliantYesProcessor SeriesHC11E
CoreHC11Data Bus Width8 bit
Data Ram Size512 BInterface TypeSCI, SPI
Maximum Clock Frequency3 MHzNumber Of Programmable I/os38
Number Of Timers8Maximum Operating Temperature+ 85 C
Mounting StyleSMD/SMTMinimum Operating Temperature- 40 C
On-chip Adc8 bit, 8 ChannelLead Free Status / RoHS StatusLead free / RoHS Compliant
Eeprom Size-Program Memory Size-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
Page 71
72
Page 72
73
Page 73
74
Page 74
75
Page 75
76
Page 76
77
Page 77
78
Page 78
79
Page 79
80
Page 80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
Page 71/124

Download datasheet (7Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
7.5 SCI Error Detection
Three error conditions, SCDR overrun, received bit noise, and framing can occur dur-
ing generation of SCI system interrupts. Three bits (OR, NF, and FE) in the serial com-
munications status register (SCSR) indicate if one of these error conditions exists. The
overrun error (OR) bit is set when the next byte is ready to be transferred from the re-
ceive shift register to the SCDR and the SCDR is already full (RDRF bit is set). When
an overrun error occurs, the data that caused the overrun is lost and the data that was
already in SCDR is not disturbed. The OR is cleared when the SCSR is read (with OR
set), followed by a read of the SCDR.
The noise flag (NF) bit is set if there is noise on any of the received bits, including the
start and stop bits. The NF bit is not set until the RDRF flag is set. The NF bit is cleared
when the SCSR is read (with FE equal to one) followed by a read of the SCDR.
When no stop bit is detected in the received data character, the framing error (FE) bit
is set. FE is set at the same time as the RDRF. If the byte received causes both fram-
ing and overrun errors, the processor only recognizes the overrun error. The framing
error flag inhibits further transfer of data into the SCDR until it is cleared. The FE bit is
cleared when the SCSR is read (with FE equal to one) followed by a read of the SCDR.
7.6 SCI Registers
There are five addressable registers in the SCI.
7.6.1 Serial Communications Data Register (SCDR)
SCDR is a parallel register that performs two functions. It is the receive data register
when it is read, and the transmit data register when it is written. Reads access the re-
ceive data buffer and writes access the transmit data buffer. Receive and transmit are
double buffered.
SCDR — SCI Data Register
Bit 7
6
R7/T7
R6/T6
RESET:
U*
U
*U = Unaffected
7.6.2 Serial Communications Control Register 1 (SCCR1)
The SCCR1 register provides the control bits that determine word length and select
the method used for the wake-up feature.
SCCR1 — SCI Control Register 1
Bit 7
6
R8
T8
RESET:
U
U
R8 — Receive Data Bit 8
If M bit is set, R8 stores the ninth bit in the receive data character.
SERIAL COMMUNICATIONS INTERFACE
TECHNICAL DATA
For More Information On This Product,
5
4
3
R5/T5
R4/T4
R3/T3
U
U
U
5
4
3
0
M
WAKE
0
0
0
Go to: www.freescale.com
$002F
2
1
Bit 0
R2/T2
R1/T1
R0/T0
U
U
U
$002C
2
1
Bit 0
0
0
0
0
0
0
7-5