R5F21236KFP#U0 Renesas Electronics America, R5F21236KFP#U0 Datasheet - Page 160

• Manufacturer Part Number: R5F21236KFP#U0
• Description: IC R8C/23 MCU FLASH 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/R8C/Tiny/23r

Specifications of R5F21236KFP#U0

• Core Processor: R8C
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: CAN, I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• For Use With: RCDK8C - KIT DEV EVAL FOR CAN R8C/23R0E521237CPE00 - EMULATOR COMPACT R8C/20/21/22/23
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/22 Group, R8C/23 Group
Rev.2.00 Aug 20, 2008
REJ09B0251-0200
14.1.3
Table 14.4
NOTE:
Count Source
Count Operations
Divide Ratio
Count Start Condition Write 1 (count starts) to the TSTART bit in the TRACR register
Count Stop
Conditions
Interrupt Request
Generation Timing
INT1/TRAIO Pin
Function
TRAO Pin Function
Read from Timer
Write to Timer
Select Functions
1. The level of output pulse turn into the level when the pulse output starts by writing the TRAMR
Event counter mode is mode to count an external signal which inputs from the INT1/TRAIO pin (see Table
14.4 Event Counter Mode Specifications).
Figure 14.8 shows the TRAIOC Register in Event Counter Mode.
register.
Item
Event Counter Mode
Event Counter Mode Specifications
Page 138 of 501
External signal which is input to TRAIO pin (active edge is selectable by a
program)
• Decrement
• When the timer underflows, the contents in the reload register is reloaded and
1/(n+1)(m+1)
n: setting value of TRAPRE register, m: setting value of TRA register
• Write 0 (count stops) to the TSTART bit in the TRACR register
• Write 1 (count forcibly stops) to the TSTOP bit in the TRACR register
When timer RA underflows [timer RA interrupt]
Count source input (INT1 interrupt input)
Programmable I/O port
The count value can be read by reading the TRA and TRAPRE registers
• When registers TRAPRE and TRA are written while the count is stopped, values
• When registers TRAPRE and TRA are written during the count, values are
• INT1 input polarity switch function
• Count source input pin select function
• Pulse output function
• Digital filter function
the count is inherited
are written to both the reload register and counter.
written to the reload register and counter (refer to 14.1.1.1 Timer Write Control
during Count Operation).
The TEDGSEL bit in the TRAIOC register can select the active edge of the
count source.
P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register.
The pulse which inverts the polarity can be output from the TRAO pin each time
the timer underflows. (selected by the TOENA bit in the TRAIOC register)
Bits TIPF0 and TIPF1 in the TRAIOC register enable or disable the digital filter
and select the sampling frequency.
(1)
Specification
14. Timers
(1)