R5F21236KFP#U0 Renesas Electronics America, R5F21236KFP#U0 Datasheet - Page 182

• Manufacturer Part Number: R5F21236KFP#U0
• Description: IC R8C/23 MCU FLASH 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/R8C/Tiny/23r

Specifications of R5F21236KFP#U0

• Core Processor: R8C
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: CAN, I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• For Use With: RCDK8C - KIT DEV EVAL FOR CAN R8C/23R0E521237CPE00 - EMULATOR COMPACT R8C/20/21/22/23
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/22 Group, R8C/23 Group
Rev.2.00 Aug 20, 2008
REJ09B0251-0200
14.2.3.1
In programmable one-shot generation mode and programmable wait one-shot generation mode, operation starts
when a one-shot trigger is generated while the TCSTF bit in the TRBCR register is set to 1 (count starts).
A one-shot trigger can be generated by either of the following causes:
When a one-shot trigger occurs, the TOSSTF bit in the TRBOCR register is set to 1 (one-shot operation in
progress) after one or two cycles of the count source have elapsed. Then, in programmable one-shot generation
mode, count operation begins and one-shot waveform output starts. (In programmable wait one-shot generation
mode, count operation starts for the wait period.) If a one-shot trigger occurs while the TOSSTF bit is set to 1,
no retriggering occurs.
To use trigger input from the INT0 pin, input the trigger after making the following settings:
Note the following points with regard to generating interrupt requests by trigger input from the INT0 pin.
•
•
•
•
•
•
•
•
•
•
1 is written to the TOSST bit in the TRBOCR register by a program.
Trigger input from the INT0 pin.
Set the PD4_5 bit in the PD4 register to 0 (input port).
Select the INT0 digital filter with bits INT0F1 and INT0F0 in the INTF register.
Select both edges or one edge with the INT0PL bit in INTEN register. If one edge is selected, further select
falling or rising edge with the INOSEG bit in TRBIOC register.
Set the INT0EN bit in the INTEN register to 0 (enabled).
After completing the above, set the INOSTG bit in the TRBIOC register to 1 (INT pin one-shot trigger
enabled).
Processing to handle the interrupts is required. Refer to 12. Interrupts for details.
If one edge is selected, use the POL bit in the INT0IC register to select falling or rising edge. (The
INOSEG bit in the TRBIOC register does not affect INT0 interrupts).
If a one-shot trigger occurs while the TOSSTF bit is set to 1, timer RB operation is not affected, but the
value of the IR bit in the INT0IC register changes.
One-Shot Trigger Selection
Page 160 of 501
14. Timers