R5F21236KFP#U0 Renesas Electronics America, R5F21236KFP#U0 Datasheet - Page 281

• Manufacturer Part Number: R5F21236KFP#U0
• Description: IC R8C/23 MCU FLASH 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/R8C/Tiny/23r

Specifications of R5F21236KFP#U0

• Core Processor: R8C
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: CAN, I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• For Use With: RCDK8C - KIT DEV EVAL FOR CAN R8C/23R0E521237CPE00 - EMULATOR COMPACT R8C/20/21/22/23
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/22 Group, R8C/23 Group
Rev.2.00 Aug 20, 2008
REJ09B0251-0200
Figure 14.109 Block Diagram of Timer RD Interrupt
14.3.11 Timer RD Interrupt
Table 14.35
Channel 0
Channel 1
Timer RD generates the Timer RD interrupt request based on 6 sources every channel. The Timer RD interrupt
has 1 TRDiIC register (IR bit, ILVL0 to ILVL2 bits) every channel, and 1 vector.
Table 14.35 lists the Registers Associated with Timer RD Interrupt and Figure 14.109 shows the Block Diagram
of Timer RD Interrupt.
As with other maskable interrupts, the timer RD interrupt is controlled by the combination of the I flag, IR bit,
bits ILVL0 to ILVL2, and IPL. However, since the interrupt source (timer RD interrupt) is generated by a
combination of multiple interrupt request sources, the following differences from other maskable interrupts
apply:
• When bits in the TRDSRi register corresponding to bits set to 1 in the TRDIERi register are set to 1 (enable
• When either bits in the TRDSRi register or bits in the TRDIERi register corresponding to bits in the
• When the conditions of other request sources are met, the IR bit remains 1.
• When multiple bits in the TRDIERi register are set to 1, which request source causes an interrupt is
• Since each bit in the TRDSRi register is not automatically set to 0 even if the interrupt is acknowledged, set
interrupt), the IR bit in the TRDiIC register is set to 1 (interrupt requested).
TRDSRi register, or both of them, are set to 0, the IR bit is set to 0 (interrupt not requested). Therefore,
even though the interrupt is not acknowledged after the IR bit is set to 1, the interrupt request will not be
maintained.
determined by the TRDSRi register.
each bit to 0 in the interrupt routine. For information on how to set these bits to 0, refer to the descriptions
of the registers used in the different modes (Figures 14.41, 14.56, 14.69, 14.81, 14.92 and 14.104).
Registers Associated with Timer RD Interrupt
i = 0 or 1
IMFA, IMFB, IMFC, IMFD, OVF, UDF: Bits in TRDSRi register
IMIEA, IMIEB, IMIEC, IMIED, OVIE: Bits in TRDIER register
TRDSR0
TRDSR1
OVIE bit
Page 259 of 501
UDF bit
OVF bit
Channel i
Status Register
Timer RD
IMIEC bit
IMIED bit
IMIEA bit
IMIEB bit
IMFC bit
IMFD bit
IMFA bit
IMFB bit
TRDIER0
TRDIER1
Interrupt Enable Register
Timer RD
Timer RD (channel i)
Interrupt request
(IR bit in TRDiIC register)
TRD0IC
TRD1IC
Interrupt Control Register
Timer RD
14. Timers