R5F21236KFP#U0 Renesas Electronics America, R5F21236KFP#U0 Datasheet - Page 55

• Manufacturer Part Number: R5F21236KFP#U0
• Description: IC R8C/23 MCU FLASH 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/R8C/Tiny/23r

Specifications of R5F21236KFP#U0

• Core Processor: R8C
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: CAN, I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• For Use With: RCDK8C - KIT DEV EVAL FOR CAN R8C/23R0E521237CPE00 - EMULATOR COMPACT R8C/20/21/22/23
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/22 Group, R8C/23 Group
Rev.2.00 Aug 20, 2008
REJ09B0251-0200
5.2
Figure 5.7
When the RESET pin is connected to the VCC pin via a pull-up resistor, and the VCC pin voltage level rises, the
power-on reset function is enabled and the MCU resets its pins, CPU, and SFR. When a capacitor is connected to
the RESET pin, too, always keep the voltage to the RESET pin 0.8VCC or more.
When the input voltage to the VCC pin reaches to the Vdet0 level or above, the low-speed on-chip oscillator clock
starts counting. When the low-speed on-chip oscillator clock count reaches 32, the internal reset signal is held “H”
and the MCU enters the reset sequence (refer to Figure 5.3). The low-speed on-chip oscillator clock divide-by-8 is
automatically selected for the CPU after reset.
Refer to 4. Special Function Registers (SFRs) for the status of the SFR after power-on reset.
The voltage monitor 0 reset is enabled after power-on reset.
Figure 5.7 shows the Example of Power-On Reset Circuit and Operation.
NOTE:
Internal reset signal
External power Vcc
NOTES:
1. When using the voltage monitor 1 digital filter, ensure VCC is 2.0 V or higher during the sampling time.
2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details.
3. Vdet1 indicates the voltage detection level of the voltage detection 1 circuit. Refer to 6. Voltage Detection Circuit for details.
4. Refer to 21. Electrical Characteristics.
5. To use the power-on reset function, enable voltage monitor 1 reset by setting the LVD1ON bit in the OFS register to 0
1. When using power-on reset function, set the LVD1ON bit to 0 (voltage monitor 1 reset enabled after reset).
(voltage monitor 1 reset enabled after reset), bits VW1C0 and VW1C6 in the VW1C register to 1 (enable) and the VCA26 bit
in the VCA2 register to 1 (voltage detection 1 circuit enabled).
(reference)
Power-On Reset Function
4.7 kΩ
(“L” valid)
V
V
det1
por1
Example of Power-On Reset Circuit and Operation
(3)
VCC
RESET
t
Page 33 of 501
w(por1)
trth
(1)
fOCO-S
1
× 32
t
d(Vdet1-A)
Sampling time
(1, 2)
2.0 V
trth
fOCO-S
1
V
por2
× 32
V
det1
(3)
5. Resets