EP2SGX90EF1152C4N Altera, EP2SGX90EF1152C4N Datasheet - Page 126

• Manufacturer Part Number: EP2SGX90EF1152C4N
• Description: IC STRATIX II GX 90K 1152-FBGA
• Manufacturer: Altera
• Series: Stratix® II GXr

Specifications of EP2SGX90EF1152C4N

• Number Of Logic Elements/cells: 90960
• Number Of Labs/clbs: 4548
• Total Ram Bits: 4520448
• Number Of I /o: 558
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 1152-FBGA
• Family Name: Stratix II GX
• Number Of Logic Blocks/elements: 90960
• # I/os (max): 558
• Frequency (max): 732.1MHz
• Process Technology: SRAM
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 90960
• Ram Bits: 4520448
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 1152
• Package Type: FC-FBGA
• For Use With: 544-1725 - PCIE KIT W/S II GX EP2SGX90N544-1724 - SI KIT W/SII GX EP2SGX90N544-1702 - VIDEO KIT W/SII GX EP2SGX90N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-1767; EP2SGX90EF35C4NES

I/O Structure
2–118
Stratix II GX Device Handbook, Volume 1
A path in which a pin directly drives a register can require the delay to
ensure zero hold time, whereas a path in which a pin drives a register
through combinational logic may not require the delay. Programmable
delays exist for decreasing input-pin-to-logic-array and IOE input
register delays. The Quartus II Compiler can program these delays to
automatically minimize setup time while providing a zero hold time.
Programmable delays can increase the register-to-pin delays for output
and/or output enable registers. Programmable delays are no longer
required to ensure zero hold times for logic array register-to-IOE register
transfers. The Quartus II Compiler can create the zero hold time for these
transfers.
devices.
The IOE registers in Stratix II GX devices share the same source for clear
or preset. You can program preset or clear for each individual IOE. You
can also program the registers to power up high or low after
configuration is complete. If programmed to power up low, an
asynchronous clear can control the registers. If programmed to power up
high, an asynchronous preset can control the registers. This feature
prevents the inadvertent activation of another device’s active-low input
upon power-up. If one register in an IOE uses a preset or clear signal, all
registers in the IOE must use that same signal if they require preset or
clear. Additionally, a synchronous reset signal is available for the IOE
registers.
Double Data Rate I/O Pins
Stratix II GX devices have six registers in the IOE, which support DDR
interfacing by clocking data on both positive and negative clock edges.
The IOEs in Stratix II GX devices support DDR inputs, DDR outputs, and
bidirectional DDR modes. When using the IOE for DDR inputs, the two
input registers clock double rate input data on alternating edges. An
input latch is also used in the IOE for DDR input acquisition. The latch
holds the data that is present during the clock high times, allowing both
bits of data to be synchronous with the same clock edge (either rising or
falling).
shows the DDR input timing diagram.
Input pin to logic array delay
Input pin to input register delay
Output pin delay
Output enable register t
Table 2–30. Stratix II GX Programmable Delay Chain
Programmable Delays
Figure 2–82
Table 2–30
shows an IOE configured for DDR input.
shows the programmable delays for Stratix II GX
CO
delay
Input delay from pin to internal cells
Input delay from pin to input register
Delay from output register to output pin
Delay to output enable pin
Quartus II Logic Option
Altera Corporation
October 2007
Figure 2–83