LPC1767FBD100,551 NXP Semiconductors, LPC1767FBD100,551 Datasheet - Page 630

• Manufacturer Part Number: LPC1767FBD100,551
• Description: IC ARM CORTEX MCU 512K 100-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1767FBD100,551

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: LPC17
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB1760, MCB1760U, MCB1760UME
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4967; 935289808551

NXP Semiconductors
UM10360
User manual
32.7.15 ISP Return Codes
Table 587. ISP Return Codes Summary
Return
Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Mnemonic
CMD_SUCCESS
INVALID_COMMAND
SRC_ADDR_ERROR
DST_ADDR_ERROR
SRC_ADDR_NOT_MAPPED
DST_ADDR_NOT_MAPPED
COUNT_ERROR
INVALID_SECTOR
SECTOR_NOT_BLANK
SECTOR_NOT_PREPARED_FOR_
WRITE_OPERATION
COMPARE_ERROR
BUSY
PARAM_ERROR
ADDR_ERROR
ADDR_NOT_MAPPED
CMD_LOCKED
INVALID_CODE
INVALID_BAUD_RATE
INVALID_STOP_BIT
CODE_READ_PROTECTION_
ENABLED
All information provided in this document is subject to legal disclaimers.
Chapter 32: LPC17xx Flash memory interface and programming
Rev. 2 — 19 August 2010
Source and destination data not equal.
Description
Command is executed successfully. Sent by ISP
handler only when command given by the host has
been completely and successfully executed.
Invalid command.
Source address is not on word boundary.
Destination address is not on a correct boundary.
Source address is not mapped in the memory map.
Count value is taken into consideration where
applicable.
Destination address is not mapped in the memory
map. Count value is taken into consideration where
applicable.
Byte count is not multiple of 4 or is not a permitted
value.
Sector number is invalid or end sector number is
greater than start sector number.
Sector is not blank.
Command to prepare sector for write operation
was not executed.
Flash programming hardware interface is busy.
Insufficient number of parameters or invalid
parameter.
Address is not on word boundary.
Address is not mapped in the memory map. Count
value is taken in to consideration where applicable.
Command is locked.
Unlock code is invalid.
Invalid baud rate setting.
Invalid stop bit setting.
Code read protection enabled.
UM10360
© NXP B.V. 2010. All rights reserved.
630 of 840