SAM3S1A Atmel Corporation, SAM3S1A Datasheet - Page 174

• Manufacturer Part Number: SAM3S1A
• Manufacturer: Atmel Corporation

Specifications of SAM3S1A

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 2
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.21.8
• STKALIGN
Indicates stack alignment on exception entry:
0 = 4-byte aligned
1 = 8-byte aligned.
On exception entry, the processor uses bit[9] of the stacked PSR to indicate the stack alignment. On return from the excep-
tion it uses this stacked bit to restore the correct stack alignment.
• BFHFNMIGN
Enables handlers with priority -1 or -2 to ignore data bus faults caused by load and store instructions. This applies to the
hard fault and FAULTMASK escalated handlers:
0 = data bus faults caused by load and store instructions cause a lock-up
1 = handlers running at priority -1 and -2 ignore data bus faults caused by load and store instructions.
Set this bit to 1 only when the handler and its data are in absolutely safe memory. The normal use of this bit is to probe sys-
tem devices and bridges to detect control path problems and fix them.
• DIV_0_TRP
Enables faulting or halting when the processor executes an SDIV or UDIV instruction with a divisor of 0:
0 = do not trap divide by 0
1 = trap divide by 0.
When this bit is set to 0,a divide by zero returns a quotient of 0.
• UNALIGN_TRP
Enables unaligned access traps:
0 = do not trap unaligned halfword and word accesses
174
31
23
15
7
SAM3S
Configuration and Control Register
Reserved
30
22
14
6
The CCR controls entry to Thread mode and enables:
See the register summary in
The bit assignments are:
• the handlers for hard fault and faults escalated by FAULTMASK to ignore bus faults
• trapping of divide by zero and unaligned accesses
• access to the STIR by unprivileged software, see
page
161.
29
21
13
5
Reserved
DIV_0_TRP
28
20
12
4
Table 10-30 on page 164
Reserved
Reserved
UNALIGN_T
RP
27
19
11
3
“Software Trigger Interrupt Register” on
Reserved
for the CCR attributes.
26
18
10
2
USERSETM
STKALIGN
PEND
25
17
9
1
6500C–ATARM–8-Feb-11
BFHFNMIGN
NONBASET
HRDENA
24
16
8
0