SAM3S1A Atmel Corporation, SAM3S1A Datasheet - Page 375

• Manufacturer Part Number: SAM3S1A
• Manufacturer: Atmel Corporation

Specifications of SAM3S1A

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 2
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

23.8.5
23.8.6
Table 23-2.
6500C–ATARM–8-Feb-11
Coded Value
setup [5:0]
pulse [6:0]
cycle [8:0]
Write Protected Registers
Coding Timing Parameters
Coding and Range of Timing Parameters
Number of Bits
To prevent any single software error that may corrupt SMC behavior, the registers listed below
can be write-protected by setting the WPEN bit in the SMC Write Protect Mode Register
(SMC_WPMR).
If a write access in a write-protected register is detected, then the WPVS flag in the SMC Write
Protect Status Register (SMC_WPSR) is set and the field WPVSRC indicates in which register
the write access has been attempted.
The WPVS flag is automatically reset after reading the SMC Write Protect Status Register
(SMC_WPSR).
List of the write-protected registers:
All timing parameters are defined for one chip select and are grouped together in one
SMC_REGISTER according to their type.
The SMC_SETUP register groups the definition of all setup parameters:
• NRD_SETUP, NCS_RD_SETUP, NWE_SETUP, NCS_WR_SETUP
The SMC_PULSE register groups the definition of all pulse parameters:
• NRD_PULSE, NCS_RD_PULSE, NWE_PULSE, NCS_WR_PULSE
The SMC_CYCLE register groups the definition of all cycle parameters:
• NRD_CYCLE, NWE_CYCLE
Table 23-2
•
•
•
•
6
7
9
Section 23.15.1 ”SMC Setup Register”
Section 23.15.2 ”SMC Pulse Register”
Section 23.15.3 ”SMC Cycle Register”
Section 23.15.4 ”SMC MODE Register”
shows how the timing parameters are coded and their permitted range.
256 x cycle[8:7] + cycle[6:0]
128 x setup[5] + setup[4:0]
256 x pulse[6] + pulse[5:0]
Effective Value
Coded Value
0 ≤ ≤ 127
0 ≤ ≤ 31
0 ≤ ≤ 63
Permitted Range
Effective Value
0 ≤ ≤ 256+127
0 ≤ ≤ 512+127
0 ≤ ≤ 768+127
0 ≤ ≤ 128+31
0 ≤ ≤ 256+63
SAM3S
375