LPC47M182 SMSC Corporation, LPC47M182 Datasheet - Page 144

no-image

LPC47M182

Manufacturer Part Number
LPC47M182
Description
ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC
Manufacturer
SMSC Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LPC47M182-NR
Manufacturer:
SMSC
Quantity:
1
Part Number:
LPC47M182-NR
Manufacturer:
SMSC
Quantity:
6 382
Part Number:
LPC47M182-NR
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
LPC47M182-NW
Manufacturer:
LINEAR
Quantity:
1 630
Part Number:
LPC47M182-NW
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
LPC47M182-NW
Manufacturer:
SMSC-Pbf
Quantity:
6
Part Number:
LPC47M182-NW
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
LPC47M182-NW
Quantity:
500
Part Number:
LPC47M182E-NW
Manufacturer:
Microchip Technology
Quantity:
10 000
7.36
Revision 1.8 SMSC/Non-SMSC Register Sets (02-24-05)
NOTE: The switch is implemented as an n-channel switch that will not pass a full voltage swing.
It provides a current path to ground.
The board designer should treat each signal pair to the switch as a separate bus with a
resistance in the path.
The maximum resistance of the switch between any bus to any other bus is 25ohms (when the
switch is on). When the switch is off the impedance is Hi-Z and the current is zero.
The design requires pull-ups on each of the busses shown above.
It is recommended that the pullups be selected so that the total maximum current on both
busses does not exceed 2mA to limit the voltage drop across the switch.
CLK GEN
DIMMS,
CNR,
ICH,
PS_ON Logic
The nPS_ON is a function of nSLP_S3 and nCPU_PRESENT according to the truth table below.
The nCPU_PRESENT is the signal from the processor that tells the system whether or not a processor
has been plugged in. The nCPU_PRESENT will be pulled to VTR through a 30uA resistor inside the chip.
The nPS_ON is used as the power down signal for the power supply. Since nPS_ON is an open drain
output, it may need to be pulled through a 1kohm resistor to V_5P0_STBY external to the chip if such a
pull-up is not provided on the power supply. The power supply turn-on circuit behaves according to the
table below.
nPS_ON
nCPU_PRESENT
nSLP_S3
SMB_CLK_M
SMB_DAT_M
PWRGD_PS
NAME
Table 7.37 – nPS_ON, nCPU_PRESENT and nSLP_S3 Pins
2.7k
VCC
Figure 7.11 – SMBUS Isolation Circuit
OD8
ISPU_400
I
2.7k
BUFFER
DATASHEET
LPC47M182
SEE NOTE
25ohm
25ohm
Max
Max
144
EN
POWER
VTR
VTR
VTR
WELL
SMB_CLK_R
SMB_DAT_R
Power Supply Turn-ON Open
Drain Output
CPU Present Input from
Processor
S3 Power State Input from
South Bridge
Advanced I/O Controller with Motherboard GLUE Logic
DESCRIPTION
2.7k
VTR
2.7k
ICH, PCI
SMSC LPC47M182
Datasheet

Related parts for LPC47M182