LPC47M182 SMSC Corporation, LPC47M182 Datasheet - Page 221

no-image

LPC47M182

Manufacturer Part Number
LPC47M182
Description
ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC
Manufacturer
SMSC Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LPC47M182-NR
Manufacturer:
SMSC
Quantity:
1
Part Number:
LPC47M182-NR
Manufacturer:
SMSC
Quantity:
6 382
Part Number:
LPC47M182-NR
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
LPC47M182-NW
Manufacturer:
LINEAR
Quantity:
1 630
Part Number:
LPC47M182-NW
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
LPC47M182-NW
Manufacturer:
SMSC-Pbf
Quantity:
6
Part Number:
LPC47M182-NW
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
LPC47M182-NW
Quantity:
500
Part Number:
LPC47M182E-NW
Manufacturer:
Microchip Technology
Quantity:
10 000
Advanced I/O Controller with Motherboard GLUE Logic
Datasheet
Chapter 15 Board Test Mode
Board level testing is implemented with an XOR Chain. The XOR chain testing allows motherboard manufacturers to
check component connectivity (e.g., opens and shorts to VCC or GND).
The TEST_EN pin is used as a strap pin to enter test mode. This pin has an internal 30 µA pull-down resistor to VSS.
An external 10 kohm pull-up to V_3P3_STBY is used to put the device in test mode.
Both VCC and VTR supplies are required for the device to operate properly in test mode.
The part enters board test (XOR-chain) mode when the TEST_EN pin is brought high. The part remains in test mode
while TEST_EN is high. Bringing TEST_EN low will exit test mode.
When the XOR chain is entered, all output and bi-directional buffers within that chain are tri-stated, except for the
XOR chain output. Every signal in the XOR chain (except for the XOR chain’s output) functions as an input. Figure
15.1 is a schematic example of XOR chain circuitry.
The XOR chain output is on pin 30, nDTR1/XOR.
The input pin ordering is as follows: the first input pin in the XOR chain is pin 1 of the chip (MCLK), and the order
continues around the chip in increasing pin number order to end at pin 128, skipping those pins that are excluded
from the chain (note that pin 117 is excluded from the chain).
The following pins are excluded from the XOR chain.
The total number of pins excluded from the XOR chain is 23; therefore there are an odd number of pins in the XOR
chain.
XOR Chain Testability Algorithm Example
An example algorithm for using the XOR chain for board test is shown below.
SMSC LPC47M182
nRSMRST pin (1)
REF5V pin (1)
REF5V_STBY pin (1)
VCC pins (5)
VTR pins (4)
V_5P0_STBY pin (1)
VSS pins (7)
F_CAP pin (1)
nDTR1/XOR pin (1)
TEST_EN pin (1)
VCC3
Pin 1
Input
Pin 2
Input
Figure 15.1 – Example XOR Chain Circuitry
DATASHEET
Pin 3
Input
221
Input
Pin 4
Pin 5
Revision 1.8 SMSC/Non-SMSC Register Sets (02-24-05)
Input
XOR Chain
Output

Related parts for LPC47M182