ST10F276Z5T3 STMicroelectronics, ST10F276Z5T3 Datasheet - Page 115

• Manufacturer Part Number: ST10F276Z5T3
• Description: MCU 16BIT 832KBIT FLASH 144-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10F276Z5T3

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: ASC, CAN, EBI/EMI, I²C, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 832KB (832K x 8)
• Program Memory Type: FLASH
• Ram Size: 68K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-TQFP, 144-VQFP
• Cpu Family: ST10
• Device Core Size: 16b
• Frequency (max): 40MHz
• Interface Type: CAN/I2C
• Total Internal Ram Size: 68KB
• # I/os (max): 111
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• On-chip Adc: 24-chx10-bit
• Instruction Set Architecture: CISC/RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Processor Series: ST10F27x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 68 KB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: 497-6399 - KIT DEV STARTER ST10F276Z5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

ST10F276Z5
Figure 28. Synchronous short / long hardware RESET (EA = 1)
1. RSTIN
2.
3. RSTIN
4.
If during the reset condition (
the asynchronous reset is then immediately entered.
cleared after reset.
Minimum
filter (refer to
RSTIN
RSTF
(After Filter)
P0[15:13]
P0[12:2]
P0[1:0]
FLARST
RST
RSTOUT
RPD
IBUS-CS
(Internal)
assertion can be released there. Refer also to Section 21.1 for details on minimum pulse duration.
pin is pulled low if bit BDRSTEN (bit 3 of SYSCON register) was previously set by software. Bit BDRSTEN is
RSTIN
Section
≤ 500 ns
≥ 50 ns
≤4 TCL
low pulse duration shall also be longer than 500 ns to guarantee the pulse is not masked by the internal
19.6).
200
4)
1)
µ
≤12 TCL
RSTIN
not t.
A Discharge
≤ 500 ns
≥ 50 ns
low), RPD voltage drops below the threshold voltage (about 2.5 V for 5 V operation),
3)
< 1032 TCL
1024 TCL
not transparent
not transparent
transparent
≤ 500 ns
≥ 50 ns
8 TCL
≤ 1 ms
2)
At this time RSTF is sampled HIGH or LOW
so it is SHORT or LONG reset
V
RPD
> 2.5 V Asynchronous Reset not entered
≤ 2 TCL
not t.
not t.
7 TCL
System reset
115/239