ST10F276Z5T3 STMicroelectronics, ST10F276Z5T3 Datasheet - Page 42

• Manufacturer Part Number: ST10F276Z5T3
• Description: MCU 16BIT 832KBIT FLASH 144-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10F276Z5T3

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: ASC, CAN, EBI/EMI, I²C, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 832KB (832K x 8)
• Program Memory Type: FLASH
• Ram Size: 68K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-TQFP, 144-VQFP
• Cpu Family: ST10
• Device Core Size: 16b
• Frequency (max): 40MHz
• Interface Type: CAN/I2C
• Total Internal Ram Size: 68KB
• # I/os (max): 111
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• On-chip Adc: 24-chx10-bit
• Instruction Set Architecture: CISC/RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Processor Series: ST10F27x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 68 KB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: 497-6399 - KIT DEV STARTER ST10F276Z5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Internal Flash memory
4.5.10
4.5.11
42/239
Table 27.
Write protection
The Flash modules have one level of Write Protections: each Sector of each Bank of each
Flash Module can be Software Write Protected by programming at 0 the related bit WyPx of
FNVWPXRH/L-FNVWPIRH/L registers.
Temporary unprotection
Bits WyPx of FNVWPXRH/L-FNVWPIRH/L can be temporary unprotected by executing the
Set Protection operation and writing 1 into these bits.
Bit ACCP can be temporary unprotected by executing the Set Protection operation and
writing 1 into these bits, but only if these write instructions are executed from the Flash
Modules.
To restore the write and access protection bits it is necessary to reset the microcontroller or
to execute a Set Protection operation and write 0 into the desired bits.
It is not necessary to temporary unprotect an access protected Flash in order to update the
code: it is, in fact, sufficient to execute the updating instructions from another Flash Bank.
In reality, when a temporary unprotection operation is executed, the corresponding volatile
register is written to 1, while the non volatile registers bits previously written to 0 (for a
protection set operation), will continue to maintain the 0. For this reason, the User software
must be in charge to track the current protection status (for instance using a specific RAM
area), it is not possible to deduce it by reading the non volatile register content (a temporary
unprotection cannot be detected).
Fetching from XRAM
Fetching from External
Memory
Summary of access protection level (continued)
Read IFLASH /
Jump to
IFLASH
No / Yes
No / Yes
Read XFLASH
/Jump to
XFLASH
Yes / Yes
Yes / Yes
Read FLASH
Registers
Yes
Yes
Write FLASH
ST10F276Z5
Registers
No
No