ST10F276Z5T3 STMicroelectronics, ST10F276Z5T3 Datasheet - Page 58

• Manufacturer Part Number: ST10F276Z5T3
• Description: MCU 16BIT 832KBIT FLASH 144-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10F276Z5T3

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: ASC, CAN, EBI/EMI, I²C, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 832KB (832K x 8)
• Program Memory Type: FLASH
• Ram Size: 68K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-TQFP, 144-VQFP
• Cpu Family: ST10
• Device Core Size: 16b
• Frequency (max): 40MHz
• Interface Type: CAN/I2C
• Total Internal Ram Size: 68KB
• # I/os (max): 111
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• On-chip Adc: 24-chx10-bit
• Instruction Set Architecture: CISC/RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Processor Series: ST10F27x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 68 KB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: 497-6399 - KIT DEV STARTER ST10F276Z5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Bootstrap loader
5.4
5.4.1
58/239
standard baud rate in this case would be 1200 baud. Baud rates below B
T6 to overflow. In this case, ASC0 cannot be initialized properly.
The maximum baud rate (B
still does not exceed the limit, that is, all baud rates between B
deviation limit. The maximum standard baud rate that fulfills this requirement is 19200 baud.
Higher baud rates, however, may be used as long as the actual deviation does not exceed
the limit. A certain baud rate (marked “I” in
limit, while an even higher baud rate (marked “II” in
depends on the host interface.
Standard bootstrap with CAN
Features
The bootstrap via CAN has the same overall behavior as the bootstrap via UART:
●
●
●
Figure 11. CAN bootstrap loader sequence
1.
2.
3.
4.
5.
6.
CAN1_RxD
CAN1_TxD
BSL initialization time, > 1ms @ fCPU = 40 MHz.
Zero frame (CAN message: standard ID = 0, DLC = 0), sent by host.
CAN message (standard ID = E6h, DLC = 3, Data0 = D5h, Data1-Data2 = IDCHIP_low-high), sent by the ST10F276Z5 on
request.
128 bytes of code / data, sent by host.
Caution: CAN1_TxD is only driven a certain time after reception of the zero byte (1.3ms @ fCPU = 40 MHz).
Internal Boot ROM / Test-Flash.
Same bootstrapping steps;
Same bootstrap method: Analyze the timing of a predefined frame, send back an
acknowledge frame BUT only on request, load a fixed number of bytes and run;
Same functionalities: Boot with different crystals and PLL ratios.
CSP:IP
RSTIN
P0L.4
1)
6)
High
2)
Int. Boot ROM / Test-Flash BSL-routine
5)
in
Figure
3)
Figure
10) is the highest baud rate where the deviation
10) may, for example, violate the deviation
4)
Figure
10) stays well below it. This
user software
Low
128bytes
and B
High
Low
are below the
would cause
ST10F276Z5