ST10F276Z5T3 STMicroelectronics, ST10F276Z5T3 Datasheet - Page 56

• Manufacturer Part Number: ST10F276Z5T3
• Description: MCU 16BIT 832KBIT FLASH 144-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10F276Z5T3

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: ASC, CAN, EBI/EMI, I²C, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 832KB (832K x 8)
• Program Memory Type: FLASH
• Ram Size: 68K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-TQFP, 144-VQFP
• Cpu Family: ST10
• Device Core Size: 16b
• Frequency (max): 40MHz
• Interface Type: CAN/I2C
• Total Internal Ram Size: 68KB
• # I/os (max): 111
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• On-chip Adc: 24-chx10-bit
• Instruction Set Architecture: CISC/RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Processor Series: ST10F27x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 68 KB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: 497-6399 - KIT DEV STARTER ST10F276Z5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Bootstrap loader
5.3.3
5.3.4
56/239
ST10 Configuration in UART BSL (RS232 or K-Line)
When the ST10F276Z5 enters BSL mode on UART, the configuration shown in
automatically set (values that deviate from the normal reset values are marked in bold).
Table 31.
1. In Bootstrap modes (standard or alternate) ROMEN, bit 10 of SYSCON, is always set regardless of EA pin
2. BUSCON0 is initialized with 0000h, external bus disabled, if pin EA is high during reset. If pin EA is low
Other than after a normal reset, the watchdog timer is disabled, so the bootstrap loading
sequence is not time limited. Pin TxD0 is configured as output, so the ST10F276Z5 can
return the acknowledge byte. Even if the internal IFLASH is enabled, a code cannot be
executed from it.
Loading the start-up code
After sending the acknowledge byte, the BSL enters a loop to receive 32 bytes via ASC0.
These bytes are stored sequentially into locations 00’FA40
allowing up to 16 instructions to be placed into the RAM area. To execute the loaded code
the BSL then jumps to location 00’FA40H, that is, the first loaded instruction. The bootstrap
loading sequence is now terminated; however, the device remains in BSL mode. The initially
loaded routine will most probably load additional code or data, as an average application is
likely to require substantially more than 16 instructions. This second receive loop may
directly use the pre-initialized interface ASC0 to receive data and store it in arbitrary user-
defined locations.
This second level of loaded code may be
●
●
●
Watchdog timer
Register SYSCON
Context Pointer CP
Register STKUN
Stack Pointer SP
Register STKOV
Register BUSCON0
Register S0CON
Register S0BG
P3.10 / TXD0
DP3.10
level. BYTDIS, bit 9 of SYSCON, is set according to data bus width selection via Port0 configuration.
during reset, BUSACT0, bit 10, and ALECTL0, bit 9, are set enabling the external bus with lengthened ALE
signal. BTYP field, bit 7 and 6, is set according to Port0 configuration.
the final application code
another, more sophisticated, loader routine that adds a transmission protocol to
enhance the integrity of the loaded code or data
a code sequence to change the system configuration and enable the bus interface to
store the received data into external memory
Function or register
ST10 configuration in UART BSL mode (RS232 or K-line)
Disabled
0400
FA00
FA00
FA40
FC00
access to startup
configuration
8011
access to ‘00’ byte
‘1’
‘1’
H
H
H
H
H
H
(1)
Access
(2)
Initialized only if Bootstrap via UART
Initialized only if Bootstrap via UART
Initialized only if Bootstrap via UART
Initialized only if Bootstrap via UART
H
through 00’FA5F
Notes
H
ST10F276Z5
of the IRAM,
Table 31
is