M30280FAHP#U5B Renesas Electronics America, M30280FAHP#U5B Datasheet - Page 110

• Manufacturer Part Number: M30280FAHP#U5B
• Description: IC M16C/28 MCU FLASH 96K 80LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30280FAHP#U5B

• Core Size: 16-Bit
• Program Memory Size: 96KB (96K x 8)
• Core Processor: M16C/60
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 71
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• Controller Family/series: M16C
• No. Of I/o's: 71
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• No. Of Timers: 10
• Digital Ic Case Style: LQFP
• Embedded Interface Type: I2C, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

M
R
R
11. DMAC
e
E
1
Figure 11.1 DMAC Block Diagram
. v
6
J
The DMAC (Direct Memory Access Controller) allows data to be transferred without the CPU intervention.
Two DMAC channels are included. Each time a DMA request occurs, the DMAC transfers one (8 or 16-bit)
data from the source address to the destination address. The DMAC uses the same data bus as used by
the CPU. Because the DMAC has higher priority of bus control than the CPU and because it makes use of
a cycle steal method, it can transfer one word (16 bits) or one byte (8 bits) of data within a very short time
after a DMA request is generated. Figure 11.1 shows the block diagram of the DMAC. Table 11.1 shows
the DMAC specifications. Figures 11.2 to 11.4 show the DMAC-related registers.
A DMA request is generated by a write to the DSR bit in the DMiSL register (i = 0,1), as well as by an
interrupt request which is generated by any function specified by the DMS and DSEL3 to DSEL0 bits in the
DMiSL register. However, unlike in the case of interrupt requests, DMA requests are not affected by the I
flag and the interrupt control register, so that even when interrupt requests are disabled and no interrupt
request can be accepted, DMA requests are always accepted. Furthermore, because the DMAC does not
affect interrupts, the IR bit in the interrupt control register does not change state due to a DMA transfer.
A data transfer is initiated each time a DMA request is generated when the DMAE bit in the DMiCON
register is set to “1” (DMA enabled). However, if the cycle in which a DMA request is generated is faster
than the DMA transfer cycle, the number of transfer requests generated and the number of times data is
transferred may not match. For details, refer to “DMA Requests”.
0
C
2
9
2 /
0 .
B
Do not use SI/04 interrupt request as a DMA request in the 64-pin package.
0
8
0
Note
0
G
4
J
7
a
o r
0 -
. n
NOTES:
u
2
1. Pointer is incremented by a DMA request.
3
p
0
, 1
0
(
M
2
DMA0 transfer counter reload register TCR0 (16)
DMA0 transfer counter TCR0 (16)
DMA1 transfer counter reload register TCR1 (16)
DMA1 transfer counter TCR1 (16)
0
1
0
6
7
C
2 /
, 8
page 88
M
1
6
C
(addresses 0029
(addresses 0039
2 /
f o
Data bus high-order bits
Data bus low-order bits
8
3
) B
8
5
16
16
, 0028
, 0038
16
16
)
)
Address bus
DMA0 destination pointer DAR0 (20)
DMA0 forward address pointer (20)
DMA1 source pointer SAR1 (20)
DMA1 destination pointer DAR1 (20)
DMA0 source pointer SAR0(20)
DMA1 forward address pointer (20)
DMA latch high-order bits
(addresses 0022
(addresses 0032
DMA latch low-order bits
(addresses 0026
(addresses 0036
16
16
(1)
(1)
to 0020
to 0030
16
16
16
16
to 0024
to 0034
)
)
16
16
)
)
11. DMAC