M30280FAHP#U5B Renesas Electronics America, M30280FAHP#U5B Datasheet - Page 376

• Manufacturer Part Number: M30280FAHP#U5B
• Description: IC M16C/28 MCU FLASH 96K 80LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30280FAHP#U5B

• Core Size: 16-Bit
• Program Memory Size: 96KB (96K x 8)
• Core Processor: M16C/60
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 71
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• Controller Family/series: M16C
• No. Of I/o's: 71
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• No. Of Timers: 10
• Digital Ic Case Style: LQFP
• Embedded Interface Type: I2C, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

M
R
R
e
E
1
. v
J
6
0
C
2
9
2 /
5. Wait until the main clock oscillation stabilization time, before switching the CPU clock source to the
6. Suggestions to reduce power consumption
0 .
B
(a) Ports
(b) A/D converter
(c) Stopping peripheral functions
(d) Switching the oscillation-driving capacity
0
0
main clock.
clock.
8
Similarly, wait until the sub clock oscillates stably before switching the CPU clock source to the sub
0
The processor retains the state of each I/O port even when it goes to wait mode or to stop mode. A
current flows in active I/O ports. A dash current may flow through the input ports in high impedance
state, if the input is floating. When entering wait mode or stop mode, set non-used ports to input and
stabilize the potential.
When A/D conversion is not performed, set the VCUT bit in ADCON1 register to “0” (no Vref connec-
tion). When A/D conversion is performed, start the A/D conversion at least 1 s or longer after setting
the VCUT bit to “1” (Vref connection).
Use the CM0 register CM02 bit to stop the unnecessary peripheral functions during wait mode.
However, because the peripheral function clock (f
this measure is not conducive to reducing the power consumption of the chip. If low speed mode or
low power dissipation mode is to be changed to wait mode, set the CM02 bit to “0” (do not peripheral
function clock stopped when in wait mode), before changing wait mode.
Set the driving capacity to “LOW” when oscillation is stable.
G
4
J
7
a
o r
0 -
. n
u
2
3
p
0
, 1
0
(
M
2
0
1
0
6
7
C
2 /
page 354
, 8
M
1
6
C
2 /
f o
8
3
) B
8
5
C32
) generated from the sub-clock does not stop,
20. Precautions