M30280FAHP#U5B Renesas Electronics America, M30280FAHP#U5B Datasheet - Page 375

• Manufacturer Part Number: M30280FAHP#U5B
• Description: IC M16C/28 MCU FLASH 96K 80LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30280FAHP#U5B

• Core Size: 16-Bit
• Program Memory Size: 96KB (96K x 8)
• Core Processor: M16C/60
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 71
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• Controller Family/series: M16C
• No. Of I/o's: 71
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• No. Of Timers: 10
• Digital Ic Case Style: LQFP
• Embedded Interface Type: I2C, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

M
R
R
e
E
1
. v
J
6
0
20.2.2 Power Control
C
2
9
2 /
1. When exiting stop mode by hardware reset, the device will startup using the on-chip oscillator.
2. Set the MR0 bit in the TAiMR register(i=0 to 4) to “0”(pulse is not output) to use the timer A to exit stop
3. When entering wait mode, insert a JMP.B instruction before a WAIT instruction. Do not excute any
Program example when entering wait mode
4. When entering stop mode, insert a JMP.B instruction immediately after executing an instruction which
Program example when entering stop mode
0 .
B
0
0
mode.
instructions which can generate a write to RAM between the JMP.B and WAIT instructions. Disable the
DMA transfers, if a DMA transfer may occur between the JMP.B and WAIT instructions. After the WAIT
instruction, insert at least 4 NOP instructions. When entering wait mode, the instruction queue reads
ahead the instructions following WAIT, and depending on timing, some of these may execute before the
microcomputer enters wait mode.
sets the CM10 bit in the CM1 register to “1”, and then insert at least 4 NOP instructions. When entering
stop mode, the instruction queue reads ahead the instructions following the instruction which sets the
CM10 bit to “1” (all clock stops), and, some of these may execute before the microcomputer enters stop
mode or before the interrupt routine for returning from stop mode.
8
0
G
4
J
7
a
o r
0 -
. n
Program Example:
Program Example:
u
2
3
p
0
, 1
0
(
M
2
0
1
0
6
7
C
2 /
page 353
, 8
M
1
6
L1:
L2:
C
2 /
f o
8
3
) B
8
JMP.B
FSET
WAIT
NOP
NOP
NOP
NOP
FSET
BSET
JMP.B
NOP
NOP
NOP
NOP
5
L1
I
I
CM10
L2
; Insert JMP.B instruction before WAIT instruction
;
; Enter wait mode
; More than 4 NOP instructions
; Enter stop mode
; Insert JMP.B instruction
; More than 4 NOP instructions
20. Precautions