M30280FAHP#U5B Renesas Electronics America, M30280FAHP#U5B Datasheet - Page 337

• Manufacturer Part Number: M30280FAHP#U5B
• Description: IC M16C/28 MCU FLASH 96K 80LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30280FAHP#U5B

• Core Size: 16-Bit
• Program Memory Size: 96KB (96K x 8)
• Core Processor: M16C/60
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 71
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• Controller Family/series: M16C
• No. Of I/o's: 71
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• No. Of Timers: 10
• Digital Ic Case Style: LQFP
• Embedded Interface Type: I2C, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

M
R
R
1
e
E
Figure 18.12 Flow Chart of Program Command
. v
6
J
18.7.3 Clear Status Register Command (50
18.7.4 Program Command (40
0
C
2
9
The clear status register command clears the status register to “0”.
By writing ‘xx50
SR5 bits in the status register are set to “0”.
The program command writes 2-byte data to the flash memory.
Auto program operation (data program and verify) start by writing ‘xx40
to the write address specified in the second bus cycle. The address value specified in the first bus cycle
must be the same even address as the write address secified in the second bus cycle.
The FMR00 bit in the FMR0 register indicates whether an auto-programming operation has been com-
pleted. The FMR00 bit is set to “0” during the auto-program and “1” when the auto-program operation is
completed.
After the completion of auto-program operation, the FMR06 bit in the FMR0 register indicates whether or
not the auto-program operation has been successfully completed. (Refer to 18.8.4 Full Status Check).
Also, each block can disable programming command (Refer to Table 18.4).
An address that is already written cannot be altered or rewritten.
When commands other than the program command are executed immediately after executing the pro-
gram command, set the same address as the write address specified in the second bus cycle of the
program command, to the specified address value in the first bus cycle of the following command.
In EW mode 1, do not execute this command on the blocks where the rewrite control program is allo-
cated.
In EW mode 0, the microcomputer enters read status register mode as soon as the auto-program opera-
tion starts and the status register can be read. The SR7 bit in the status register is set to “0” as soon as the
auto-program operation starts. This bit is set to “1” when the auto-program operation is completed. The
microcomputer remains in read status register mode until the read array command is written. After
completion of the auto-program operation, the status register indicates whether or not the auto-program
operation has been successfully completed.
2 /
0 .
B
0
8
0
0
G
4
J
7
a
o r
0 -
. n
u
2
3
p
0
, 1
0
(
M
2
0
1
0
6
16
7
C
2 /
’ in the first bus cycle, and the FMR06 to FMR07 bits in the FMR0 register and SR4 to
page 315
, 8
M
NOTES:
1
6
1. Write the command code and data at even address.
2. Refer to Figure 18.15 .
C
2 /
f o
8
3
) B
8
5
Write data to the write address
Write command code "xx40
16
)
the write address
Full status check
Program completed
FMR00=1?
Start
YES
16
)
(2)
(1)
NO
16
" to
(1)
16
’ in the first bus cycle and data
18. Flash Memory Version