AT89C51SND2C-7FTUL Atmel, AT89C51SND2C-7FTUL Datasheet - Page 156

• Manufacturer Part Number: AT89C51SND2C-7FTUL
• Description: IC 8051 MCU FLASH 64K MP3 100BGA
• Manufacturer: Atmel
• Series: 89Cr

Specifications of AT89C51SND2C-7FTUL

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, IDE/ATAPI, MMC, SPI, UART/USART, USB
• Peripherals: Audio, I²S, MP3, PCM, POR, WDT
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.3 V
• Data Converters: A/D 2x10b; D/A 2x20b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: ATAPI, I2S, IDE, SPI, UART, USB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: AT89C51SND2C7FTUL

19. Synchronous Peripheral Interface
Figure 19-1. Typical Master SPI Bus Configuration
Figure 19-2. Typical Slave SPI Bus Configuration
156
AT8xC51SND2C/MP3B
AT8xC51SND2C
MASTER
The AT8xC51SND2C implements a Synchronous Peripheral Interface with master and slave
modes capability.
Figure 19-1 shows an SPI bus configuration using the AT8xC51SND2C as master connected to
slave peripherals while Figure 19-2 shows an SPI bus configuration using the AT8xC51SND2C
as slave of an other master.
The bus is made of three wires connecting all the devices together:
•
•
•
Each slave peripheral is selected by one Slave Select pin (SS). If there is only one slave, it may
be continuously selected with SS tied to a low level. Otherwise, the AT8xC51SND2C may select
each device by software through port pins (Pn.x). Special care should be taken not to select 2
slaves at the same time to avoid bus conflicts.
MISO
MOSI
SCK
SSn
SS1
SS0
P4.0
P4.1
P4.2
Pn.z
Pn.y
Pn.x
Master Output Slave Input (MOSI): it is used to transfer data in series from the master to a
slave.
It is driven by the master.
Master Input Slave Output (MISO): it is used to transfer data in series from a slave to the
master.
It is driven by the selected slave.
Serial Clock (SCK): it is used to synchronize the data transmission both in and out the
devices through their MOSI and MISO lines. It is driven by the master for eight clock cycles
which allows to exchange one Byte on the serial lines.
MISO
MOSI
SCK
SS
SS
SO
SO
DataFlash 1
Slave 1
SI
SI
SCK
SCK
SS
SS
SO
SO
DataFlash 2
Slave 2
SI
SI
SCK
SCK
MISO MOSI SCK
SS
AT8xC51SND2C
SS
SO
Slave n
Controller
SI
LCD
SCK
4341H–MP3–10/07