MC68HC908JK8CP Freescale Semiconductor, MC68HC908JK8CP Datasheet - Page 132

• Manufacturer Part Number: MC68HC908JK8CP
• Manufacturer: Freescale Semiconductor

Specifications of MC68HC908JK8CP

• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SCI
• Program Memory Type: Flash
• Program Memory Size: 8KB
• Total Internal Ram Size: 256Byte
• # I/os (max): 15
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 13-chx8-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 20
• Package Type: PDIP
• Lead Free Status / Rohs Status: Not Compliant

Serial Communications Interface (SCI)
9.4.3.7 Receiver Interrupts
The following sources can generate CPU interrupt requests from the SCI receiver:
9.4.3.8 Error Interrupts
The following receiver error flags in SCS1 can generate CPU interrupt requests:
132
•
•
•
•
•
•
•
•
Address mark — An address mark is a logic 1 in the most significant bit position of a received
character. When the WAKE bit is set, an address mark wakes the receiver from the standby state
by clearing the RWU bit. The address mark also sets the SCI receiver full bit, SCRF. Software can
then compare the character containing the address mark to the user-defined address of the
receiver. If they are the same, the receiver remains awake and processes the characters that
follow. If they are not the same, software can set the RWU bit and put the receiver back into the
standby state.
Idle input line condition — When the WAKE bit is clear, an idle character on the RxD pin wakes the
receiver from the standby state by clearing the RWU bit. The idle character that wakes the receiver
does not set the receiver idle bit, IDLE, or the SCI receiver full bit, SCRF. The idle line type bit,
ILTY, determines whether the receiver begins counting logic 1s as idle character bits after the start
bit or after the stop bit.
SCI receiver full (SCRF) — The SCRF bit in SCS1 indicates that the receive shift register has
transferred a character to the SCDR. SCRF can generate a receiver CPU interrupt request. Setting
the SCI receive interrupt enable bit, SCRIE, in SCC2 enables the SCRF bit to generate receiver
CPU interrupts.
Idle input (IDLE) — The IDLE bit in SCS1 indicates that 10 or 11 consecutive logic 1s shifted in
from the RxD pin. The idle line interrupt enable bit, ILIE, in SCC2 enables the IDLE bit to generate
CPU interrupt requests.
Receiver overrun (OR) — The OR bit indicates that the receive shift register shifted in a new
character before the previous character was read from the SCDR. The previous character remains
in the SCDR, and the new character is lost. The overrun interrupt enable bit, ORIE, in SCC3
enables OR to generate SCI error CPU interrupt requests.
Noise flag (NF) — The NF bit is set when the SCI detects noise on incoming data or break
characters, including start, data, and stop bits. The noise error interrupt enable bit, NEIE, in SCC3
enables NF to generate SCI error CPU interrupt requests.
Framing error (FE) — The FE bit in SCS1 is set when a logic 0 occurs where the receiver expects
a stop bit. The framing error interrupt enable bit, FEIE, in SCC3 enables FE to generate SCI error
CPU interrupt requests.
Parity error (PE) — The PE bit in SCS1 is set when the SCI detects a parity error in incoming data.
The parity error interrupt enable bit, PEIE, in SCC3 enables PE to generate SCI error CPU interrupt
requests.
With the WAKE bit clear, setting the RWU bit after the RxD pin has been
idle may cause the receiver to wake up immediately.
MC68HC908JL8/JK8 • MC68HC08JL8/JK8 • MC68HC908KL8 Data Sheet, Rev. 3.1
NOTE
Freescale Semiconductor