UPD70F3737GC-UEU-AX Renesas Electronics America, UPD70F3737GC-UEU-AX Datasheet - Page 423

• Manufacturer Part Number: UPD70F3737GC-UEU-AX
• Description: MCU 32BIT V850ES/JX3-L 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Lr

Specifications of UPD70F3737GC-UEU-AX

• Package / Case: *
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 20MHz
• Number Of I /o: 84
• Core Processor: RISC
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Program Memory Size: 128KB (128K x 8)
• Data Converters: A/D 12x10b, D/A 2x8b
• Oscillator Type: Internal
• Peripherals: DMA, LVD, PWM, WDT
• Connectivity: CSI, EBI/EMI, I²C, UART/USART
• Core Size: 32-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

12.5 Usage
12.6 Cautions
(1) Disable real-time output.
(2) Perform initialization as follows.
(3) Enable real-time output.
(4) Set the next output value to the RTBH0 and RTBL0 registers by the time the selected transfer trigger is
(5) Set the next real-time output value to the RTBH0 and RTBL0 registers via interrupt servicing corresponding to
(1) Prevent the following conflicts by software.
(2) Before performing initialization, disable real-time output (RTPOE0 bit = 0).
(3) Once real-time output has been disabled (RTPOE0 bit = 0), be sure to initialize the RTBH0 and RTBL0
• Set the alternate-function pins of port 5
• Specify the real-time output port mode or port mode in 1-bit units.
• Channel configuration: Select the trigger and valid edge.
• Set the initial values to the RTBH0 and RTBL0 registers
the selected trigger.
Notes 1. If the RTBH0 and RTBL0 registers are written when the RTPOE0 bit = 0, that value is transferred
• Conflict between real-time output disable/enable switching (RTPOE0 bit) and selected real-time output
• Conflict between writing to the RTBH0 and RTBL0 registers in the real-time output enabled status and the
Clear the RTPC0.RTPOE0 bit to 0.
Set the RTPOE0 bit = 1.
generated
registers before enabling real-time output again (RTPOE0 bit = 0 → 1).
Set the PFC5.PFC5m bit and PFCE5.PFCE5m bit to 1, and then set the PMC5.PMC5m bit to 1 (m = 0 to 5).
Set the RTPM0 register.
Set the RTPC0.EXTR0, RTPC0.BYTE0, and RTPC0.RTPEG0 bits.
trigger.
selected real-time output trigger.
2. Even if the RTBH0 and RTBL0 registers are written when the RTPOE0 bit = 1, data is not
Note 2
to real-time output latches 0H and 0L, respectively.
transferred to real-time output latches 0H and 0L.
.
CHAPTER 12 REAL-TIME OUTPUT FUNCTION (RTO)
Preliminary User’s Manual U18953EJ1V0UD
Note 1
.
423