UPD70F3737GC-UEU-AX Renesas Electronics America, UPD70F3737GC-UEU-AX Datasheet - Page 636

• Manufacturer Part Number: UPD70F3737GC-UEU-AX
• Description: MCU 32BIT V850ES/JX3-L 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Lr

Specifications of UPD70F3737GC-UEU-AX

• Package / Case: *
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 20MHz
• Number Of I /o: 84
• Core Processor: RISC
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Program Memory Size: 128KB (128K x 8)
• Data Converters: A/D 12x10b, D/A 2x8b
• Oscillator Type: Internal
• Peripherals: DMA, LVD, PWM, WDT
• Connectivity: CSI, EBI/EMI, I²C, UART/USART
• Core Size: 32-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

636
(5) DMA channel control registers 0 to 3 (DCHC0 to DCHC3)
Notes 1. The TCn bit is read-only.
Cautions 1. Be sure to clear bits 6 to 3 of the DCHCn register to 0.
The DCHC0 to DCHC3 registers are 8-bit registers that control the DMA transfer operating mode for DMA
channel n.
These registers can be read or written in 8-bit or 1-bit units. (However, bit 7 is read-only and bits 1 and 2 are
write-only. If bit 1 or 2 is read, the read value is always 0.)
Reset sets these registers to 00H.
2. The INITn and STGn bits are write-only.
2. When DMA transfer is completed (when a terminal count is generated), the Enn bit is
(n = 0 to 3)
cleared to 0 and then the TCn bit is set to 1. If the DCHCn register is read while its bits are
being updated, a value indicating “transfer not completed and transfer is disabled” (TCn bit
= 0 and Enn bit = 0) may be read.
DCHCn
After reset:
INITn
STGn
TCn
TCn
It is set to 1 on the last DMA transfer and cleared to 0 when it is read.
DMA transfer is enabled when the Enn bit is set to 1.
When DMA transfer is completed (when a terminal count is generated), this bit is
automatically cleared to 0.
To abort DMA transfer, clear the Enn bit to 0 by software. To resume, set the Enn
bit to 1 again.
When aborting or resuming DMA transfer, however, be sure to observe the
procedure described in 18.13 Cautions.
00H
Enn
<7>
0
1
0
1
CHAPTER 18 DMA FUNCTION (DMA CONTROLLER)
Note 1
Note 1
Note 2
Note 2
DMA transfer had not completed.
DMA transfer had completed.
If the INITn bit is set to 1 with DMA transfer disabled (Enn bit = 0), the
DMA transfer status can be initialized.
When re-setting the DMA transfer status (re-setting the DDAnH, DDAnL,
DSAnH, DSAnL, DBCn, and DADCn registers) before DMA transfer is
completed (before the TCn bit is set to 1), be sure to initialize the DMA
channel.
When initializing the DMA controller, however, be sure to observe the
procedure described in 18.13 Cautions.
This is a software startup trigger of DMA transfer.
If this bit is set to 1 in the DMA transfer enable state (TCn bit = 0, Enn
bit = 1), DMA transfer is started.
DMA transfer disabled
DMA transfer enabled
R/W
Preliminary User’s Manual U18953EJ1V0UD
0
6
Address:
through DMA channel n has completed or not
5
0
DMA channel n is to be enabled or disabled
Status flag indicates whether DMA transfer
Setting of whether DMA transfer through
DCHC0 FFFFF0E0H, DCHC1 FFFFF0E2H,
DCHC2 FFFFF0E4H, DCHC3 FFFFF0E6H
0
4
3
0
INITn
<2>
Note 2
STGn
<1>
Note 2
Enn
<0>