HD64F2676VFC33 Renesas Electronics America, HD64F2676VFC33 Datasheet - Page 474

• Manufacturer Part Number: HD64F2676VFC33
• Description: IC H8S MCU FLASH 256K 144-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2600r

Specifications of HD64F2676VFC33

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 33MHz
• Connectivity: IrDA, SCI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 103
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 4x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 9 Data Transfer Controller (DTC)
9.7.2
An example of DTC chain transfer is shown in which pulse output is performed using the PPG.
Chain transfer can be used to perform pulse output data transfer and PPG output trigger cycle
updating. Repeat mode transfer to the PPG’s NDR is performed in the first half of the chain
transfer, and normal mode transfer to the TPU’s TGR in the second half. This is because clearing
of the activation source and interrupt generation at the end of the specified number of transfers are
restricted to the second half of the chain transfer (transfer when CHNE = 0).
1. Perform settings for transfer to the PPG’s NDR. Set MRA to source address incrementing
2. Perform settings for transfer to the TPU’s TGR. Set MRA to source address incrementing
3. Locate the TPU transfer register information consecutively after the NDR transfer register
4. Set the start address of the NDR transfer register information to the DTC vector address.
5. Set the bit corresponding to TGIA in DTCER to 1.
6. Set TGRA as an output compare register (output disabled) with TIOR, and enable the TGIA
7. Set the initial output value in PODR, and the next output value in NDR. Set bits in DDR and
8. Set the CST bit in TSTR to 1, and start the TCNT count operation.
9. Each time a TGRA compare match occurs, the next output value is transferred to NDR and the
10. When the specified number of transfers are completed (the TPU transfer CRA value is 0), the
Rev. 3.00 Mar 17, 2006 page 422 of 926
REJ09B0283-0300
(SM1 = 1, SM0 = 0), fixed destination address (DM1 = DM0 = 0), repeat mode (MD1 = 0,
MD0 = 1), and word size (Sz = 1). Set the source side as a repeat area (DTS = 1). Set MRB to
chain mode (CHNE = 1, DISEL = 0). Set the data table start address in SAR, the NDRH
address in DAR, and the data table size in CRAH and CRAL. CRB can be set to any value.
(SM1 = 1, SM0 = 0), fixed destination address (DM1 = DM0 = 0), normal mode (MD1 = MD0
= 0), and word size (Sz = 1). Set the data table start address in SAR, the TGRA address in
DAR, and the data table size in CRA. CRB can be set to any value.
information.
interrupt with TIER.
NDER for which output is to be performed to 1. Using PCR, select the TPU compare match to
be used as the output trigger.
set value of the next output trigger period is transferred to TGRA. The activation source TGFA
flag is cleared.
TGFA flag is held at 1, the DTCE bit is cleared to 0, and a TGIA interrupt request is sent to the
CPU. Termination processing should be performed in the interrupt handling routine.
Chain Transfer