PIC12F1840-I/P Microchip Technology, PIC12F1840-I/P Datasheet - Page 262

• Manufacturer Part Number: PIC12F1840-I/P
• Description: 7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core 8 PDI
• Manufacturer: Microchip Technology

Specifications of PIC12F1840-I/P

• Processor Series: PIC12F
• Core: PIC
• Program Memory Type: Flash
• Program Memory Size: 7 KB
• Data Ram Size: 256 B
• Interface Type: MI2C, SPI, EUSART
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-8
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12(L)F1840
REGISTER 25-3:
DS41441B-page 262
bit 7
Legend:
R = Readable bit
u = Bit is unchanged
‘1’ = Bit is set
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
R/W-0/0
GCEN
For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I
set (no spooling) and the SSP1BUF may not be written (or writes to the SSP1BUF are disabled).
GCEN: General Call Enable bit (in I
1 = Enable interrupt when a general call address (0x00 or 00h) is received in the SSP1SR
0 = General call address disabled
ACKSTAT: Acknowledge Status bit (in I
1 = Acknowledge was not received
0 = Acknowledge was received
ACKDT: Acknowledge Data bit (in I
In Receive mode:
Value transmitted when the user initiates an Acknowledge sequence at the end of a receive
1 = Not Acknowledge
0 = Acknowledge
ACKEN: Acknowledge Sequence Enable bit (in I
In Master Receive mode:
1 = Initiate Acknowledge sequence on SDA and SCL pins, and transmit ACKDT data bit.
0 = Acknowledge sequence Idle
RCEN: Receive Enable bit (in I
1 = Enables Receive mode for I
0 = Receive Idle
PEN: Stop Condition Enable bit (in I
SCK Release Control:
1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Stop condition Idle
RSEN: Repeated Start Condition Enabled bit (in I
1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Repeated Start condition Idle
SEN: Start Condition Enabled bit (in I
In Master mode:
1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Start condition Idle
In Slave mode:
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)
0 = Clock stretching is disabled
ACKSTAT
R-0/0
Automatically cleared by hardware.
SSP1CON2: SSP1 CONTROL REGISTER 2
W = Writable bit
x = Bit is unknown
‘0’ = Bit is cleared
R/W-0/0
ACKDT
R/S/HS-0/0
2
ACKEN
2
C Master mode only)
C
Preliminary
2
2
2
C mode only)
C Slave mode only)
C Master mode only)
2
C Master mode only)
2
C mode only)
U = Unimplemented bit, read as ‘0’
-n/n = Value at POR and BOR/Value at all other Resets
HC = Cleared by hardware
R/S/HS-0/0
2
RCEN
C module is not in the Idle mode, this bit may not be
2
2
C Master mode only)
C Master mode only)
R/S/HS-0/0
PEN
 2011 Microchip Technology Inc.
S = User set
R/S/HS-0/0
RSEN
R/W/HS-0/0
SEN
bit 0