PIC12F1840-I/P Microchip Technology, PIC12F1840-I/P Datasheet - Page 90

• Manufacturer Part Number: PIC12F1840-I/P
• Description: 7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core 8 PDI
• Manufacturer: Microchip Technology

Specifications of PIC12F1840-I/P

• Processor Series: PIC12F
• Core: PIC
• Program Memory Type: Flash
• Program Memory Size: 7 KB
• Data Ram Size: 256 B
• Interface Type: MI2C, SPI, EUSART
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-8
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12(L)F1840
9.1.1
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
• If the interrupt occurs before the execution of a
FIGURE 9-1:
DS41441B-page 90
Instruction Flow
SLEEP instruction
- SLEEP instruction will execute as a NOP.
- WDT and WDT prescaler will not be cleared
- TO bit of the STATUS register will not be set
- PD bit of the STATUS register will not be
(INTCON reg.)
Note
Interrupt flag
GIE bit
Instruction
Fetched
Instruction
Executed
CLKOUT
cleared.
OSC1
1:
2:
3:
4:
PC
(1)
(2)
WAKE-UP USING INTERRUPTS
XT, HS or LP Oscillator mode assumed.
CLKOUT is not available in XT, HS or LP Oscillator modes, but shown here for timing reference.
T
GIE = 1 assumed. In this case after wake-up, the processor calls the ISR at 0004h. If GIE = 0, execution will continue in-line.
OST
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Inst(PC) = Sleep
Inst(PC - 1)
= 1024 T
PC
WAKE-UP FROM SLEEP THROUGH INTERRUPT
OSC
(drawing not to scale). This delay applies only to XT, HS or LP Oscillator modes.
Inst(PC + 1)
Sleep
PC + 1
Processor in
Sleep
PC + 2
Preliminary
T
OST (3)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Interrupt Latency
Inst(PC + 2)
Inst(PC + 1)
• If the interrupt occurs during or after the execu-
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
PC + 2
tion of a SLEEP instruction
- SLEEP instruction will be completely exe-
- Device will immediately wake-up from Sleep
- WDT and WDT prescaler will be cleared
- TO bit of the STATUS register will be set
- PD bit of the STATUS register will be cleared.
cuted
(4)
Dummy Cycle
PC + 2
 2011 Microchip Technology Inc.
Dummy Cycle
Inst(0004h)
0004h
Inst(0005h)
Inst(0004h)
0005h