S9S12HY64J0MLL Freescale Semiconductor, S9S12HY64J0MLL Datasheet - Page 247

• Manufacturer Part Number: S9S12HY64J0MLL
• Description: MCU 64K FLASH AUTO 100-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12HY64J0MLL

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-LQFP
• Controller Family/series: S12
• No. Of I/o's: 80
• Ram Memory Size: 4KB
• Cpu Speed: 64MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: S12HY
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12HY64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Freescale Semiconductor
WRTMASK
RSBCK
CR[2:0]
WCOP
Field
2–0
7
6
5
Window COP Mode Bit — When set, a write to the CPMUARMCOP register must occur in the last 25% of the
selected period. A write during the first 75% of the selected period generates a COP reset. As long as all writes
occur during this window, $55 can be written as often as desired. Once $AA is written after the $55, the time-out
logic restarts and the user must wait until the next window before writing to CPMUARMCOP.
the duration of this window for the seven available COP rates.
0 Normal COP operation
1 Window COP operation
COP and RTI Stop in Active BDM Mode Bit
0 Allows the COP and RTI to keep running in Active BDM mode.
1 Stops the COP and RTI counters whenever the part is in Active BDM mode.
Write Mask for WCOP and CR[2:0] Bit — This write-only bit serves as a mask for the WCOP and CR[2:0] bits
while writing the CPMUCOP register. It is intended for BDM writing the RSBCK without changing the content of
WCOP and CR[2:0].
0 Write of WCOP and CR[2:0] has an effect with this write of CPMUCOP
1 Write of WCOP and CR[2:0] has no effect with this write of CPMUCOP.
COP Watchdog Timer Rate Select — These bits select the COP time-out rate (see
nonzero value to CR[2:0] enables the COP counter and starts the time-out period. A COP counter time-out
causes a System Reset. This can be avoided by periodically (before time-out) initializing the COP counter via
the CPMUARMCOP register.
While all of the following four conditions are true the CR[2:0], WCOP bits are ignored and the COP operates at
highest time-out period (
(Does not count for “write once”.)
1) COP is enabled (CR[2:0] is not 000)
2) BDM mode active
3) RSBCK = 0
4) Operation in special mode
CR2
0
0
0
0
1
1
1
1
MC9S12HY/HA-Family Reference Manual, Rev. 1.04
Table 7-11. CPMUCOP Field Descriptions
2
24
CR1
Table 7-12. COP Watchdog Rates
cycles) in normal COP mode (Window COP mode disabled):
0
0
1
1
0
0
1
1
S12 Clock, Reset and Power Management Unit (S12CPMU) Block Description
CR0
0
1
0
1
0
1
0
1
Description
(COPCLK is either IRCCLK or
OSCCLK depending on the
Cycles to time-out
COPOSCSEL bit)
COP disabled
COPCLK
2
2
2
2
2
2
2
14
16
18
20
22
23
24
Table
7-12). Writing a
Table 7-12
shows
247