S9S12HY64J0MLL Freescale Semiconductor, S9S12HY64J0MLL Datasheet - Page 633

• Manufacturer Part Number: S9S12HY64J0MLL
• Description: MCU 64K FLASH AUTO 100-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12HY64J0MLL

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-LQFP
• Controller Family/series: S12
• No. Of I/o's: 80
• Ram Memory Size: 4KB
• Cpu Speed: 64MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: S12HY
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12HY64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.3.2.9.1
The general guideline is that P-Flash protection can only be added and not removed.
all valid transitions between P-Flash protection scenarios. Any attempt to write an invalid scenario to the
FPROT register will be ignored. The contents of the FPROT register reflect the active protection scenario.
See the FPHS and FPLS bit descriptions for additional restrictions.
17.3.2.10 D-Flash Protection Register (DFPROT)
The DFPROT register defines which D-Flash sectors are protected against program and erase operations.
The (unreserved) bits of the DFPROT register are writable with the restriction that protection can be added
but not removed. Writes must increase the DPS value and the DPOPEN bit can only be written from 1
(protection disabled) to 0 (protection enabled). If the DPOPEN bit is set, the state of the DPS bits is
irrelevant.
During the reset sequence, the DFPROT register is loaded with the contents of the D-Flash protection byte
in the Flash configuration field at global address 0x3_FF0D located in P-Flash memory (see
as indicated by reset condition F in
during the reset sequence, the P-Flash sector containing the D-Flash protection byte must be unprotected,
then the D-Flash protection byte must be programmed. If a double bit fault is detected while reading the
Freescale Semiconductor
Offset Module Base + 0x0009
Reset
W
R
DPOPEN
F
7
P-Flash Protection Restrictions
1
Protection
Allowed transitions marked with X, see
Scenario
From
= Unimplemented or Reserved
0
1
2
3
4
5
6
7
0
0
6
Table 17-20. P-Flash Protection Scenario Transitions
Figure 17-15. D-Flash Protection Register (DFPROT)
MC9S12HY/HA-Family Reference Manual, Rev. 1.04
X
X
0
Figure
0
0
5
X
X
X
X
1
17-15. To change the D-Flash protection that will be loaded
X
X
X
X
2
To Protection Scenario
0
0
4
Figure 17-14
X
X
X
X
X
X
X
X
3
X
X
X
X
4
for a definition of the scenarios.
F
3
1
5
X
X
64 KByte Flash Module (S12FTMRC64K1V1)
F
2
X
X
6
DPS[3:0]
Table 17-20
X
7
F
1
Table
specifies
F
0
17-3)
633