LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 117

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

NXP Semiconductors
UM10237_4
User manual
Table 116. Connection of interrupt sources to the Vectored Interrupt Controller
Block
UART1
PWM0,
PWM1
I
SPI, SSP0
SSP 1
PLL
RTC
System
Control
(External
Interrupts)
ADC0
I
BOD
Ethernet
USB
2
2
C0
C1
Flag(s)
Rx Line Status (RLS)
Transmit Holding Register Empty (THRE)
Rx Data Available (RDA)
Character Time-out Indicator (CTI)
Modem Control Change
End of Auto-Baud (ABEO)
Auto-Baud Time-Out (ABTO)
Match 0 - 6 of PWM0
Capture 0 of PWM0
Match 0 - 6 of PWM1
Capture 0-1 of PWM1
SI (state change)
SPI Interrupt Flag of SPI (SPIF)
Mode Fault of SPI (MODF)
Tx FIFO half empty of SSP0
Rx FIFO half full of SSP0
Rx Timeout of SSP0
Rx Overrun of SSP0
Tx FIFO half empty
Rx FIFO half full
Rx Timeout
Rx Overrun
PLL Lock (PLOCK)
Counter Increment (RTCCIF)
Alarm (RTCALF)
Subsecond Int (RTCSSF)
External Interrupt 0 (EINT0)
External Interrupt 1 (EINT1)
External Interrupt 2 (EINT2)/LCD
Remark: The LCD is available on LPC247x only. The LCD
interrupt is shared with EINT2 if bit 20 (PCLCD) is set in
Table 4–63 “Power Control for Peripherals register
(PCONP - address 0xE01F C0C4) bit
External Interrupt 3 (EINT3).
Note: EINT3 channel is shared with GPIO interrupts
A/D Converter 0 end of conversion
SI (state change)
Brown Out detect
WakeupInt, SoftInt, TxDoneInt, TxFinishedInt,
TxErrorInt, TxUnderrunInt, RxDoneInt,
RxFinishedInt, RxErrorInt, RxOverrunInt.
USB_INT_REQ_LP, USB_INT_REQ_HP,
USB_INT_REQ_DMA
Rev. 04 — 20 August 2009
Chapter 7: LPC24XX Vectored Interrupt Controller (VIC)
description”.
VIC Channel # and
Hex Mask
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
UM10237
© NXP B.V. 2009. All rights reserved.
0x0000 0080
0x0000 0100
0x0000 0200
0x0000 0400
0x0000 0800
0x0000 1000
0x0000 2000
0x0000 4000
0x0000 8000
0x0001 0000
0x0002 0000
0x0004 0000
0x0008 0000
0x0010 0000
0x0020 0000
0x0040 0000
117 of 792