LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 618

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

NXP Semiconductors
7. FIFO controller
UM10237_4
User manual
When switching between data width or modes the I2S must be reset via the reset bit in the
control register in order to ensure correct synchronization. It is advisable to set the stop bit
also until sufficient data has been written in the transmit FIFO. Note that when stopped
data output is muted.
All data accesses to FIFO's are 32 bits.
sequences.
A data sample in the FIFO consists of:
Data is read from the transmit FIFO after the falling edge of WS, it will be transferred to
the transmit clock domain after the rising edge of WS. On the next falling edge of WS the
left data will be loaded in the shift register and transmitted and on the following rising edge
of WS the right data is loaded and transmitted.
The receive channel will start receiving data after a change of WS. When word select
becomes low it expects this data to be left data, when WS is high received data is
expected to be right data. Reception will stop when the bit counter has reached the limit
set by wordwidth. On the next change of WS the received data will be stored in the
appropriate hold register. When complete data is available it will be written into the receive
FIFO.
Handling of data for transmission and reception is performed via the FIFO controller which
can generate two DMA requests and an interrupt request. The controller consists of a set
of comparators which compare FIFO levels with depth settings contained in registers. The
current status of the level comparators can be seen in the APB status register.
•
•
•
•
•
•
Data word length is determined by the wordwidth value in the configuration register.
There is a separate wordwidth value for the receive channel and the transmit channel.
– 0: word is considered to contain four 8 bits data words.
– 1: word is considered to contain two 16 bits data words.
– 3: word is considered to contain one 32 bits data word.
When the transmit FIFO contains insufficient data the transmit channel will repeat
transmitting the last data until new data is available. This can occur when the
microprocessor or the DMA at some time is unable to provide new data fast enough.
Because of this delay in new data there is a need to fill the gap, which is
accomplished by continuing to transmit the last sample. The data is not muted as this
would produce an noticeable and undesirable effect in the sound.
The transmit channel and the receive channel only handle 32 bit aligned words, data
chunks must be clipped or extended to a multiple of 32 bits.
1×32 bits in 8 or 16 bit stereo modes.
1×32 bits in mono modes.
2×32 bits, first left data, second right data, in 32 bit stereo modes.
Rev. 04 — 26 August 2009
Figure 23–128
Chapter 23: LPC24XX I
shows the possible data
UM10237
© NXP B.V. 2009. All rights reserved.
2
S interface
618 of 792