LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 749

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

NXP Semiconductors
UM10237_4
User manual
3.1.1 RMHost
3.1.2 RMTarget
3.1 RealMonitor components
processor context saving and restoring. RealMonitor is pre-programmed in the on-chip
ROM memory (boot sector). When enabled It allows user to observe and debug while
parts of application continue to run. Refer to
page 751
As shown in
This is located between a debugger and a JTAG unit. The RMHost controller,
RealMonitor.dll, converts generic Remote Debug Interface (RDI) requests from the
debugger into DCC-only RDI messages for the JTAG unit. For complete details on
debugging a RealMonitor-integrated application from the host, see the ARM RMHost User
Guide (ARM DUI 0137A).
This is pre-programmed in the on-chip ROM memory (boot sector), and runs on the target
hardware. It uses the EmbeddedICE logic, and communicates with the host using the
DCC. For more details on RMTarget functionality, see the RealMonitor Target Integration
Guide (ARM DUI 0142A).
Fig 149. RealMonitor components
target
host
for details.
Figure
REALMONITOR.DLL
TARGET BOARD AND
PROCESSOR
35–149, RealMonitor is split in to two functional components:
Rev. 04 — 26 August 2009
DCC transmissions
over the JTAG link
Section 35–4 “How to enable RealMonitor” on
APPLICATION
DEBUGGER
RMTARGET
JTAG UNIT
RMHOST
RDI 1.5.1 RT
RDI 1.5.1
Chapter 35: LPC24XX RealMonitor
UM10237
© NXP B.V. 2009. All rights reserved.
RealMonitor
protocol
749 of 792