LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 451

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

NXP Semiconductors
UM10237_4
User manual
wished to send a 105 character message and the trigger level was 10 characters, the
CPU would receive 10 RDA interrupts resulting in the transfer of 100 characters and 1 to 5
CTI interrupts (depending on the service routine) resulting in the transfer of the remaining
5 characters.
Table 403. UART1 Interrupt Handling
[1]
[2]
[3]
[4]
The UART1 THRE interrupt (U1IIR[3:1] = 001) is a third level interrupt and is activated
when the UART1 THR FIFO is empty provided certain initialization conditions have been
met. These initialization conditions are intended to give the UART1 THR FIFO a chance to
fill up with data to eliminate many THRE interrupts from occurring at system start-up. The
initialization conditions implement a one character delay minus the stop bit whenever
THRE = 1 and there have not been at least two characters in the U1THR at one time since
the last THRE = 1 event. This delay is provided to give the CPU time to write data to
U1THR without a THRE interrupt to decode and service. A THRE interrupt is set
immediately if the UART1 THR FIFO has held two or more characters at one time and
currently, the U1THR is empty. The THRE interrupt is reset when a U1THR write occurs or
a read of the U1IIR occurs and the THRE is the highest interrupt (U1IIR[3:1] = 001).
U1IIR[3:0]
value
0001
0110
0100
1100
0010
0000
Values "0000", “0011”, “0101”, “0111”, “1000”, “1001”, “1010”, “1011”,”1101”,”1110”,”1111” are reserved.
For details see
For details see
Read Only)”
For details see
and
Only)”
[1]
Section 17–4.2 “UART1 Transmitter Holding Register (U1THR - 0xE001 0000 when DLAB = 0, Write
Priority Interrupt
-
Highest RX Line
Second RX Data
Second Character
Third
Fourth
Section 17–4.5 “UART1 Interrupt Identification Register (U1IIR - 0xE001 0008, Read Only)”
Section 17–4.11 “UART1 Line Status Register (U1LSR - 0xE001 0014, Read Only)”
Section 17–4.1 “UART1 Receiver Buffer Register (U1RBR - 0xE001 0000, when DLAB = 0
Type
None
Status /
Error
Available
Time-out
indication
THRE
Modem
Status
Rev. 04 — 26 August 2009
Interrupt Source
None
OE
Rx data available or trigger level reached in FIFO
(U1FCR0=1)
Minimum of one character in the RX FIFO and no
character input or removed during a time period
depending on how many characters are in FIFO
and what the trigger level is set at (3.5 to 4.5
character times).
The exact time will be:
[(word length) × 7 - 2] × 8 + [(trigger level - number
of characters) × 8 + 1] RCLKs
THRE
CTS or DSR or RI or DCD
[2]
or PE
[2]
[2]
or FE
[2]
or BI
[2]
Chapter 17: LPC24XX UART1
UM10237
© NXP B.V. 2009. All rights reserved.
Interrupt
Reset
-
U1LSR
Read
U1RBR
Read
UART1
FIFO drops
below
trigger level
U1RBR
Read
U1IIR
Read
source of
interrupt) or
THR write
MSR Read
451 of 792
[2]
[3]
[3]
[4]
or
(if