LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 85

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

NXP Semiconductors
UM10237_4
User manual
10.12 Dynamic Memory Write Recovery Time register (EMCDynamictWR -
10.13 Dynamic Memory Active to Active Command Period register
Table 78.
0xFFE0 8044)
The EMCDynamicTWR register enables you to program the write recovery time, tWR. It is
recommended that this register is modified during system initialization, or when there are
no current or outstanding transactions. This can be ensured by waiting until the EMC is
idle, and then entering low-power, or disabled mode. This value is normally found in
SDRAM data sheets as tWR, tDPL, tRWL, or tRDL. This register is accessed with one
wait state.
Note: This register is used for all four dynamic memory chip selects. Therefore the worst
case value for all of the chip selects must be programmed.
Table 5–79
Table 79.
(EMCDynamictRC - 0xFFE0 8048)
The EMCDynamicTRC register enables you to program the active to active command
period, tRC. It is recommended that this register is modified during system initialization, or
when there are no current or outstanding transactions. This can be ensured by waiting
until the EMC is idle, and then entering low-power, or disabled mode. This value is
normally found in SDRAM data sheets as tRC. This register is accessed with one wait
state.
Note: This register is used for all four dynamic memory chip selects. Therefore the worst
case value for all of the chip selects must be programmed.
Table 5–80
Bit
3:0
31:4
Bit
3:0
31:4
Symbol
Data-in to active
command
(tDAL)
-
Symbol
Write recovery
time (tWR)
-
Dynamic Memory Data-in to Active Command Time register (EMCDynamictDAL -
address 0xFFE0 8040) bit description
Dynamic Memory Write recover Time register (EMCDynamictWR - address
0xFFE0 8044) bit description
shows the bit assignments for the EMCDynamicTWR register.
shows the bit assignments for the EMCDynamicTRC register.
Rev. 04 — 26 August 2009
Value Description
0x0 -
0xE
0xF
-
Value Description
0x0 -
0xE
0xF
-
Chapter 5: LPC24XX External Memory Controller (EMC)
n clock cycles. The delay is in CCLK cycles.
15 clock cycles (POR reset value).
Reserved, user software should not write ones to
reserved bits. The value read from a reserved bit is not
defined.
n + 1 clock cycles. The delay is in CCLK cycles.
16 clock cycles (POR reset value).
Reserved, user software should not write ones to
reserved bits. The value read from a reserved bit is not
defined.
UM10237
© NXP B.V. 2009. All rights reserved.
85 of 792
Reset
Value
0xF
NA
Reset
Value
0xF
NA