LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 394

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

1. Basic configuration
2. Introduction
3. Features
4. Architecture
UM10237_4
User manual
The USB controller is configured using the following registers:
This chapter describes the OTG and I
controller which integrates the (OHCI) host controller, device controller, and I
interface (Master only) controls an external OTG transceiver.
USB OTG (On-The-Go) is a supplement to the USB 2.0 specification that augments the
capability of existing mobile devices and USB peripherals by adding host functionality for
connection to USB peripherals. The specification and more information on USB OTG can
be found on the USB Implementers Forum web site.
The architecture of the USB OTG controller is shown below in the block diagram.
The host, device, OTG, and I2C controllers can be programmed through the register
interface. The OTG controller enables dynamic switching between host and device roles
through the HNP protocol. One port may be connected to an external OTG transceiver to
1. Power: In the PCONP register
2. Clock: see
3. Pins: Select USB pins and their modes in PINSEL0 to PINSEL5 and PINMODE0 to
4. Wakeup: Use the INTWAKE register
5. Interrupts: See
6. Initialization: see
•
•
•
•
UM10237
Chapter 15: LPC24XX USB OTG controller
Rev. 04 — 26 August 2009
Remark: On reset, the USB block is disabled (PCUSB = 0).
PINMODE5
port to wakeup the microcontroller from Power-down mode (see
VICIntEnable register
Fully compliant with On-The-Go supplement to the USB 2.0 Specification, Revision
1.0a.
Hardware support for Host Negotiation Protocol (HNP).
Includes a programmable timer required for HNP and SRP.
Supports any OTG transceiver compliant with the OTG Transceiver Specification
(CEA-2011), Rev. 1.0.
Table
(Section
Section
4–54.
Section
Rev. 04 — 26 August 2009
9–5).
(Section
15–7.16. Interrupts are enabled in the VIC using the
15–10.
(Table
7–3.4).
2
C portions of the USB 2.0 OTG dual role device
(Table
4–63), set bit PCUSB.
4–62) to enable activity on the USB bus
Section
© NXP B.V. 2009. All rights reserved.
User manual
2
15–9.2).
C. The I
394 of 792
2
C