LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 714

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

NXP Semiconductors
UM10237_4
User manual
Fig 145. GPDMA in the LPC24XX
EXTERNAL
MEMORY
4.2.4 Channel Logic and Channel Register Bank
4.2.5 Interrupt Request
4.2.6 AHB Master Interface
4.2.7 Bus and transfer widths
4.2.8 Endian behavior
The channel logic and channel register bank contains registers and logic required for each
DMA channel.
The interrupt request generates interrupts to the ARM processor.
The GPDMA contains a full AHB master. See
connected in the LPC24XX.
The AHB master is capable of dealing with all types of AHB transactions, including:
The physical width of the AHB bus is 32 bits. Source and destination transfers can be of
differing widths, and can be the same width or narrower than the physical bus width. The
GPDMA packs or unpacks data as appropriate.
The GPDMA can cope with both little-endian and big-endian addressing. You can set the
endianness of each AHB master individually.
Internally the GPDMA treats all data as a stream of bytes instead of 16 bit or 32 bit
quantities. This means that when performing mixed-endian activity, where the endianness
of the source and destination are different, byte swapping of the data within the 32 bit data
bus is observed.
Note: If you do not require byte swapping then avoid using different endianness between
the source and destination addresses.
CONTROLLER
EXTERNAL
•
•
•
MEMORY
Split, retry, and error responses from slaves. If a peripheral performs a split or retry,
the GPDMA stalls and waits until the transaction can complete.
Locked transfers for source and destination of each stream.
Setting of protection bits for transfers on each stream.
BRIDGE
ARM7
AHB
Chapter 32: LPC24XX General Purpose DMA (GPDMA) controller
Rev. 04 — 26 August 2009
AHB1
SLAVE
AHB
GPDMA
SRAM
16 kB
MASTER
AHB
Figure 32–145
BRIDGE
APB
for how the GPDMA is
UM10237
SD/MMC
© NXP B.V. 2009. All rights reserved.
SSP1
SSP0
I2S1
I2S0
714 of 792