LPC2468FBD208,551 NXP Semiconductors, LPC2468FBD208,551 Datasheet - Page 406

• Manufacturer Part Number: LPC2468FBD208,551
• Description: IC ARM7 MCU FLASH 512K 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4261; 935282457551; LPC2468FBD208-S

NXP Semiconductors
UM10237_4
User manual
7.10 I2C Receive Register (I2C_RX - 0xFFE0 C300)
7.12 I2C Status Register (I2C_STS - 0xFFE0 C304)
7.11 I2C Transmit Register (I2C_TX - 0xFFE0 C300)
Table 369. OTG_clock_status register (OTGClkSt - address 0xFFE0 CFF8) bit description
This register is the top byte of the receive FIFO. The receive FIFO is 4 bytes deep. The Rx
FIFO is flushed by a hard reset or by a soft reset (I2C_CTL bit 7). Reading an empty FIFO
gives unpredictable data results.
Table 370. I2C Receive register (I2C_RX - address 0xFFE0 C300) bit description
This register is the top byte of the transmit FIFO. The transmit FIFO is 4 bytes deep.
The Tx FIFO is flushed by a hard reset, soft reset (I2C_CTL bit 7) or if an arbitration failure
occurs (I2C_STS bit 3). Data writes to a full FIFO are ignored.
I2C_TX must be written for both write and read operations to transfer each byte. Bits [7:0]
are ignored for master-receive operations. The master-receiver must write a dummy byte
to the TX FIFO for each byte it expects to receive in the RX FIFO. When the STOP bit is
set or the START bit is set to cause a RESTART condition on a byte written to the TX
FIFO (master-receiver), then the byte read from the slave is not acknowledged. That is,
the last byte of a master-receive operation is not acknowledged.
Table 371. I2C Transmit register (I2C_TX - address 0xFFE0 C300) bit description
The I2C_STS register provides status information on the TX and RX blocks as well as the
current state of the external buses. Individual bits are enabled as interrupts by the
I2C_CTL register and routed to the I2C_USB_INT bit in USBIntSt.
Bit
4
31:5
Bit
7:0
Bit
7:0
8
9
31:10 -
Symbol
RX Data
Symbol
AHB_CLK_ON
-
Symbol
TX Data
START
STOP
Description
Transmit data.
When 1, issue a START condition before transmitting this byte.
When 1, issue a STOP condition after transmitting this byte.
Reserved. User software should not write ones to reserved bits. The
value read from a reserved bit is not defined.
Rev. 04 — 26 August 2009
Description
Receive data.
Value Description
0
1
NA
AHB master clock status.
AHB clock is not available.
AHB clock is available.
Reserved, user software should not write ones
to reserved bits. The value read from a
reserved bit is not defined.
Chapter 15: LPC24XX USB OTG controller
UM10237
© NXP B.V. 2009. All rights reserved.
406 of 792
Reset
Value
0
NA
-
Reset
Value
-
-
-
Reset
Value
-