OM13013,598 NXP Semiconductors, OM13013,598 Datasheet - Page 341
OM13013,598
Manufacturer Part Number
OM13013,598
Description
BOARD DEMO IAR LPC1227 JLINKLITE
Manufacturer
NXP Semiconductors
Series
-r
Specifications of OM13013,598
Design Resources
LPC122x-SK Brd Schematic
Processor To Be Evaluated
LPC1227
Processor Series
LPC122x
Data Bus Width
32 bit
Interface Type
UART, SSP, SPI, I2C
Cpu Core
ARM Cortex-M0
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3 V to 3.6 V
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-6885
- Current page: 341 of 442
- Download datasheet (3Mb)
NXP Semiconductors
UM10441
User manual
21.7.4.3 Auto-request cycle
21.7.4.4 Ping-pong cycle
When the controller operates in this mode, it is only necessary for it to receive a single
request to enable it to complete the entire DMA cycle. This enables a large data transfer
to occur, without significantly increasing the latency for servicing higher priority requests
or requiring multiple requests from the processor or peripheral.
The auto-request cycle is typically used for memory-to-memory requests. In this case,
software generates the starting request for the 2
control data structure.
In this mode, the controller can be configured to use either the primary or the alternate
channel control data structure. After the channel is enabled and the controller receives a
request for this channel, the flow for the auto-request cycle is as follows:
In this mode, the controller performs a DMA cycle using one of the data structures and
then performs a DMA cycle using the other data structure. The controller continues to
switch between primary and alternate structures until it reads a data structure that is
invalid, until the user reprograms the cycle_type to basic, or until the host processor
disables the channel.
In ping-pong mode, the user can program or reprogram one of the two channel data
structures (primary or alternate) while using the other channel data structure for the active
transfer. When a transfer is done, the next transfer can be started immediately using the
prepared channel data structure - provided that a higher priority channel does not require
servicing. If the user does not reprogram the channel control data structure not in use for
a transfer, the cycle type remains invalid (which is the value at the end of the last transfer
using that structure), and the ping-pong cycle completes.
The ping-pong cycle can be used for transfers to or from peripherals or for
memory-to-memory transfers.
3. The controller sets dma_done[c] signal for this channel HIGH for one system clock
1. The controller performs 2
2. The controller arbitrates if there are any transfers remaining after 2
3. The controller sets dma_done[c] signal for this channel HIGH for one system clock
cycle. This indicates to the host processor that the DMA cycle is complete.
flow continues at step 3.
current channel c has the highest priority, the cycle continues at step 1.
cycle. This indicates to the host processor that the DMA cycle is complete.
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 February 2011
Chapter 21: LPC122x General purpose micro DMA controller
R
transfers. If the number of transfers remaining is zero the
R
transfers after setting up the DMA
UM10441
R
© NXP B.V. 2011. All rights reserved.
transfers. If the
341 of 442
Related parts for OM13013,598
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: