MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 1043

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

24.13.1 Ownership Trace Messaging
Ownership trace information is messaged via the auxiliary port using an ownership trace message (OTM).
The ownership trace register (OT), which can be accessed via auxiliary port, is updated by the operating
system software to provide task/process ID information. When new information is updated in the register
by the embedded processor, it is messaged out via the auxiliary port, allowing development tools to trace
ownership flow.
Ownership trace information is messaged out in the following format:
24.13.2 Queue Overflow Ownership Trace Error Message
A program/data/ownership trace overrun error occurs when a trace message cannot be queued due to the
queue being full, provided ownership trace is enabled.
The overrun error causes the message queue to be flushed, and a error message to be queued. The error
code within the error message indicates that a program/data/ownership trace overrun error has occurred.
Refer to
The error message has the following format:
24.13.2.1 OTM Flow
Ownership trace messages are generated when the operating system (privileged supervisor task) writes to
the memory-mapped ownership trace register.
The following flow describes the OTM process.
Freescale Semiconductor
1. The OT register is a memory-mapped register, whose address is located in the UBA. The OT
2. Only privileged writes (byte/half word or word) initiated by the RCPU to the OT register that
3. OT register reads and non-privileged OT register writes, or writes initiated by any source other than
register address can be read from the UBA register by the IEEE-ISTO 5001 tool.
terminate normally are valid. The data value (word) written into the register is formed into the
ownership trace message that is queued to be transmitted.
the RCPU, do not cause ownership trace messages to be transmitted by the READI module.
Table
24-20.
Figure 24-74. Ownership Trace Message Format
TCODE (2)
MPC561/MPC563 Reference Manual, Rev. 1.2
TCODE (8)
[6 bits]
Figure 24-75. Error Message Format
[6 bits]
Length = 38 bits
Length = 11 bits
Task/Process ID Tag
[32 bits]
Error Code (0b0 0000,
0b0 0001, 0b0 0010,
0b0 0111)
[5 bits]
READI Module
24-75