MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 303

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

Chapter 8
Clocks and Power Control
The main timing reference for the MPC561/MPC563 can monitor any of the following:
The system operating frequency is generated through a programmable phase-locked loop, the system PLL
(SPLL). The SPLL runs at twice the system speed. The SPLL is programmable in integer multiples of the
input frequency to generate the internal (VCO/2) operating frequency. A pre-divider before the SPLL
enables the division of the high frequency crystal oscillator. The internal operating SPLL frequency should
be at least 30 MHz. It can be divided by a power-of-two divider to generate the system operating
frequencies.
In addition to the system clock, the clocks submodule provides the following:
The oscillator, TB, DEC, RTC, and the PIT are powered from the keep alive power supply (KAPWR) pin.
This allows the counters to continue to increment/decrement at the oscillator frequency even when the
main power to the MCU is off. While the power is off, the PIT may be used to signal the power supply IC
to enable power to the system at specific intervals. This is the power-down wake-up feature. When the chip
is not in power-down low-power mode, the KAPWR is powered to the same voltage value as the voltage
of the I/O buffers and logic.
The MPC561/MPC563 clock module consists of the main crystal oscillator, the SPLL, the low-power
divider, the clock generator, the system low-power control block, and the limp mode control block. The
clock module receives control bits from the system clock control register (SCCR), change of lock interrupt
register (COLIR), the PLL low-power and reset-control register (PLPRCR), and the PLL.
Freescale Semiconductor
•
•
•
•
•
An external crystal with a frequency of 4 or 20 MHz
An external frequency source with a frequency of 4 MHz
An external frequency source at the system frequency
TMBCLK to the time base (TB) and decrementer (DEC)
PITRTCLK to the periodic interrupt timer (PIT) and real-time clock (RTC)
MPC561/MPC563 Reference Manual, Rev. 1.2
8-1